0
The major benefit of a switch over a hub is the increase in the amount of collision domains. This allows a switched network to benefit from full duplex transmissions, negating the need for CSMA/CD, and doubling the potential throughput for each network segment. Switches typically operate at layer 2 of the OSI model, using destination MAC addresses within the Ethernet frame to intelligently filter or forward packets.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What do switches do?
A switch is a device that segments networks into different subnets. Segmenting the network into different subnets keeps one network from overloading with traffic. Therefore, a switch forwards all data in the data layer and sometimes the network layer as it filters the data. A switch allows a connection to be established and it terminates a connection when there is no longer a session to support. Prior to switches there were hubs. Hubs also connected multiple independent (connected) modules in a network, but they were not as efficient as switches. Since most switches work in Layer 2, and not in Layer 1 like a hub, they are better at filtering data. A switch looks for Ethernet MAC addresses, keeps a table (the bridge forwarding table) of these addresses, and navigates the switch between ports. The switch prevents collisions and gives full bandwidth to each connection at the switch port. Switches save bandwidth by only sending traffic to destinations that have traffic. When a switch switches Ethernet frames, they monitor the traffic for the response from that frame and see what device, on what port, responds to that flooded frame. There are different types of switches that range from "dumb" switches that lack manageability and can monitor only 4-8 ports to "managed" switches that can get statistics on switch traffic, monitor connections, and hard-code up to 96 port speeds and duplex. Then again, there are "chassis-based" switches with blades or cards that perform not just switching, but routing and intrusion detection too! If you are interested in this, look into Cisco's Catalyst 6500 Series. Another type of switch preferred by large enterprises is the "Layer 3 Switch," because it has the functionality of a router .
Where are the hubs for sky west located?
where are the hubs for sky west airline located The hubs for Sky West are Chicago O' Hare, Denver, Houston, Los Angeles, Minneapolis/St. Paul, Phoenix, Portland, Salt Lake City, San Francisco and Seattle. I retrieved this information from their website skywest.com, under facts. Heather P.
You got a 92 GEO Tracker 4x4 manual hubs AT and you have reverse but no Low 2nd or Drive why might this be and how do you fix this problem for the cheapest and easyiest way on your own?
well man im sorry to say but it sounds like your trany is blown. so it needs replaced or rebuilt. and so u know im haveing my AT rebuilt right now and its putting me back $600.
What are facts about Al-qaeda?
Al- Qaeda is an international terrorism organization of Islamic extremists who were started by Osama Bin Laden. They operate mostly in Afghanistan and Pakistan, although the groups has hubs throughout the Middle East.there previous leader osama bin laden once shot a man for snoringthey defeated the soviet russian in the 1980'sthey failed an attack in 1993 to take down the wtc with a garage bomb
Why is maintaining biodiversity important?
That way if there is a loss of one entire species entire ecosystems aren't effected so heavily, also it is what keeps life going.
Advantage of using switches rather than hubs?
See related link
How do hubs segregate packets?
Hubs segregate packets because hubs are used as switches. Through a VLAN, hubs, when used as switches, can easily segregate incoming and outgoing traffic.
What is max no of hops in hypercube network to go from one node to another?
This depends on if you are using hubs or switches.
Why it is easier to scan a network that is connected with Hubs rather than with Switches?
It is easier to scan a network connected by hubs than by switches because a switch can limit traffic between subnets, whereas a hub cannot, and would therefore require more overhead to facilitate a scan.
What are the purposes of switches and hubs?
Switches increase the number of collision domains in the network.
When is the appropriate time to replace hubs with switches?
As soon as possible. Switches are much more efficient than hubs because hubs send the data to all the connect nodes, unlike switches that only forward packets to the appropriate node. Hubs cause a lot of packet collisions which reduces the efficiency of your network. __________________ I was going to say "Now, because switches are so cheap". But your answer is better.
Where can I find a magazine about network hubs and switches?
There is no magazine that is specific to network hubs and switches. However, PC Magazine is a computer magazine available on newsstands and MozillaQuest (http://mozillaquest.com/index.html) is an online magazine that may include articles and other information on network hubs and switches.
What is the diff between hubs and switches?
Please see:What_is_the_difference_between_a_hub_and_a_switch
What connects networks of the same type?
Switches, hubs...
Which usually connects a LAN togeather?
hubs, switches or routers.
What distinguishes switches from repeating devices such as hubs?
layer 3 switches require ip address but hub do not require
A network backbone is the WHAT that connects the hubs switches and routers on a network?
cabling
