0
What is the cable classification for 10base5 thickness coaxail?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the temperature rating of non-metallic sheathed cable?
You have to check on the sheathing itself but mostly all household wiring is rated for 600 volts. I think you will find that NMS is rated at 300 volts.
What is the trade name for this cable romex?
NM (Non Metallic) Cable.
What type of cable gives off little or no toxic fumes when burned?
The cable is not the problem the protective coating on the cable is. MilSpec cable is very hard to burn the cable, normal cable coatings when burned give off toxic gases depending on what the coating is made of.
What is a cable terminal?
A cable terminal is a fixture designed to be installed in the end of a cable or conductor in order to facilitate the connection.
What is difference between core cable and pair cable?
The term core represents each individual conductor within a cable, and a pair is two cores (or two conductors) within a cable. For example if you have a 3 core cable, then the cable has 3 separate conductors in it (3 separate cables within the PVC coating). A 3 pair cable would be 3 sets of 2 cores, so this would have 6 conductors within the cable.
Blank Ethernet uses thick RG8 coaxial cable with an AUI connector?
10base5
Does a 10Base5 Ethernet used twisted-pair cabling rated CAT-3 or higher and an RJ-45 connector?
No, 10Base5 uses coaxial cable (RG-6) with an F connector
What cable can be used to connect a transceiver to the cable in a thicknet network?
Thicknet coax cables are 10base5 cables, RG-8 or RG-6 cables.
What thickness cable require for 415 volt?
Voltage determines a cable's insulation thickness, not its conductor thickness (or, more accurately, its cross-sectional area). It's current that determines the csa of a conductor, not voltage.
What kind of wiring is commonly used in a bus topology?
A bus topology for a LAN will typically use coaxial cable, either 10Base5 (thicknet) or 10base2 (thin-net) copper wiring.
What is the actual loss of voltage in 100 meter length of cable?
It depends on the material of the cable (aluminum or copper) and the gauge of the cable. (Thickness). And on the current you intend it to carry.
How do you you measure the thickness of a thin wire?
To measure the thickness of a thin piece of wire we have got the instrument called the wire gauge. The thickness of a thin piece of wire is measured in mm.
What is AWG in cable?
American Wire Gauge. Measure the thickness of the cable.
How can you define number of modes in optical fiber?
A definition on top of my head, it's the number of frequencies allowed to be carried by the Optical Fiber Cable, It depends on the Ko, thickness and Numerical Aperture of the Fiber Cable.
What are fiber optic cable made up of?
they e made up of glass which is strewn to around the same thickness as a hair fibre (strand of hair)
What is the difference between thicknet and thinnet cables?
Thicknet or 10BASE5 is able to run 500 meters. Thinnet or 10BASE2 is able to run 185 meters. Thinnet cable has a smaller diameter (it is thinner cable) and is more flexible and so easier to work with than thicknet. In the old days you would run a thicknet cable in the ceiling as your network backbone and use vampire taps to attach thinnet cables ("drop cables") that would drop down into rooms in the office where they would connect to hubs. This setup is caled a bus topology. The problem was if that if any piece wasn't properly terminated or is any one cable broke then the whole network went down and you'd have to run around trying to locate the break.
How do you cut an armoured cable?
The use of armoured cable is determined by the application that needs an electrical source of voltage. It is a metal sheath cable classification. Armoured cable is used in applications that need mechanical protection usually below a certain elevation. Armoured cable is also usually used on surface wiring. If you have access to an electrical code book there is a whole section on armoured cable. In the CEC the section about armoured cable starts at 12-600 to 12-618.
