Want this question answered?
The two molecules must collide with the correct orientation and with a minimum amount of energy (called the activation energy).
It is used to show the correct length that the wire has to be stripped to make a perfect termination. By using this mark no bare conductor will be exposed when the plug is assembled for use.
Translation is process in which the mRNA is read by ribosomes to make protein.The translation completes in these steps: initiation,elongation and termination.Activation of amino acids - amino acid is joined to the correct tRNAInitiation: Initiation Factor (IF-2-GTP) guides the first tRNA (tRNAifmet) to the P site. The large ribosomal subunit then arrives.Elongation:(a)Codon recognition: The second tRNA with amino acid arrives at the A site (guided by Elogation Factor (EF-Tu)(b)Peptide bond formation: A peptide bond is formed between the first and second amino acids.(c)Translocation: The 1st tRNA moves to the E site (and exits) and 2nd tRNA moves to the P site. Now the A site is again available for next tRNA.This process of polypeptide chain elongation continues until a stop codon (the region of base triplet of mRNA where the polypeptide chain is complete and released) is reached.Termination: A release factor binds to the A site. It carries no amino acid but facilitate the release of the polypeptide, the ribosome and tRNA from the mRNA.
It decreases the activation energy, or the energy barrier the reactants must go through to form products. This is the same thing as the energy of the transition state. By decreasing the activation energy necessary for the reaction to occur, more reactants are able to form products since not as much energy is needed. See the Web Links to the left of this answer for more information.
The rate of reaction often increases when catalysts are added. Catalysts can either lower the activation energy required for the reaction to happen, so that means more molecules will have enough energy to react than if the activation energy were higher. Catalysts can also be like substrates that act as a site for holding the molecules in the correct position to react. Always remember that molecules need to collide in the correct position with enough energy in order to react, and so catalysts will aid these two requirements and increase the reaction rate. There are catalysts that slow the reaction, but it's not common.
RNA polymerase reaches the beginning of a gene.
The major steps of translation are:Translation takes place in the cytoplasm, where tRna,rRNA, and mRNA interact to assemble proteins. A specific amino acid is added to one end of each tRNA. The other end of the tRNA has an anticodon. A anticodon is a three-nucleotide seqence on tRNA that is complementary to an mRNA codon. The mRNA joins with a ribosome and tRNA. A tRNA molecule that has the correct anticodon and amino acid binds to the second codon on the mRNA. A peptide bond forms between the two amino acids, and the tRNA is realeased from the ribosome. The ribosome hen moves one codon down the MRNA. The amino acid chain continues to grow as each new amino acid binds to the chain and the pervious tRNA is released. This process is repeated until one of three stop codons is reached. A stop codon does not have anticodon, so protien production stops.
The correct answers are A), 4], and Ernest Hemingway.
That is the correct spelling of the noun "termination" (ending, killing, or firing).
calcification, resting, proliferation, hypertrophication
Rovio is the answer...This is the correct activation key. Please trust me.
zone of cell division-zone of elongation-zone of maturation
I think you mean super eruption, which refers to teeth that continues to erupt unopposed after it is already in the correct position.
activation of G protein, binding of GTP, activation of adenylate cyclase, conversion of ATP to cAMP
Activation of G protein, binding of GTP, activation of adenylate cyclase, conversion of ATP to cAMP
The two molecules must collide with the correct orientation and with a minimum amount of energy (called the activation energy).
it is a tool used for checking patch cables and testing for correct termination of a cable at the patch panal and jack.