0
What else can I help you with?
What is the volt drop across a 10k resistor with a 5 volt supply?
If there is nothing else in the circuit, then the voltage drop across the resistor will be the full supply voltage of 5 volts. The size of the resistor does not matter in this case - it will always be 5 volts.
What would the voltage be if you had 78 volts with a parallel circuit of 10k 10k 10k 10k 5k?
because the circuit you have quoted is a parrallel type, the voltage will be the same across all the components/ resistors in parallel . -- 78 volts. however i wonder if you needed to calcualte the current flow
How do you determine the 10k resistor?
A 10K resistor has the coloured stripes in the following order.. Brown, Black, Orange, Gold
How would you connect a resistor in order to reduce an LED's applied voltage?
You could use the voltage divider rule to reduce the voltage. Using two resistors in series, the input voltage will drop across each resistor by an amount that is proportionate to the values of the resistors. If the 1st resistor is 10K and the 2nd resistor is 100K, the voltage drop across the 10K will be 10 times LESS than that of the 100K resistor. The total voltage drop across both resistors will be equal to the supplied input voltage. Work out the ratio of voltage you need from the total input voltage and use 2 resistors will that give you the same ratio. Connect the LEDs in parallel with the resistor the gives you the voltage you want. Use a MM to measure the voltage across the resistor before wiring LEDs.
What current does the input required to give an output on Lm741?
It depends on the shunt feedback resistor on the op-amp, for example with a 10k feedback resistor connecting the output to the inverting input, 1 mA input current gives 10 volts signal output. The input terminal stays near zero voltage because of the high open-loop gain of the op-amp, so the inverting input is termed a 'virtual earth'.
How much voltage is required to cause 8mill of current to flow through a 10kilo resistor?
V = IR = 8x10-3 (8 mA) * 10x103 (10k) = 80v
What is different between the resistor and pullup resistor?
A "pull-up" resistor is a resistor used to to perform a specific electronic function - it is not a different type of resistor. A very small current flows through a pull-up resistor so it does not need to be high wattage (1/8 watt is generally fine). The value of a pull-up resistor depends on the resistance of the sensor. If it is simply on or off (no resistance) then a typical pull-up resistor might be 10k ohms.
What does 10k resistor do?
Resistance: Electrical resistance describes how an electrical conductor (a wire) opposes the flow of an electrical current (flow of electrons). To overcome this opposition a voltage (a energy) must dropped (used) across the conductor (wire). Resistance can be described by ohms law: Ohms Law: R = V / I (Resistance = Voltage / Current) (resistance measured in ohms) where: Voltage [V]= the energy lost across an component (voltage measured in volts). Current [I] = the charge (electrons) flowing through an component (current measured in Amps). Electrical resistance can be thought of as sticking your hand out a car window. The faster [current] you drive the harder the wind presses [resistance] against you hand and therefore it takes more energy [voltage] to hold your hand steady. When trying to overcome electrical resistance, the electrical energy lost is turned into heat. This is how the elements of a household stove, toaster, and fan heater work. Because of the vacuum in a light bulb, the electrical energy lost is instead turned into light. It can be seen the electrical resistance plays a large role in modern life. Resistor: The resistor is the most common electronic component and is used to limit and/or control the voltage and current in an electronic circuit. Resistors are carefully manufactured to provide a predetermined value of electrical resistance which may range from 0.1 ohms to 100,000,000 ohms, depending on the application. The physical size of a resistor also varies dependant on the amount of power passing through the resistor, given by: P = V x I (Power = Voltage x Current) (power measured in watts) There are also many types of resistors including: · Variable Resistor - changes resistance when its shaft is rotated (volume knob on a stereo). · Thermistor - changes resistance when the temperature changes (used in a thermostat). · Light Dependant Resistor (LDR) - changes resistance when the lighting changes (used in children's night-lights). Resistor Example: An LED is a small red light (such as the one on the front of most TVs) and requires 2.0 volts and 0.02 amps to operate correctly. If we connected that LED up directly to a 12 volt battery, the voltage would be too high, and too much current would flow… the LED would blow up. We need to use a resistor to limit the voltage and current. But which value of resistance should the have resistor? Uses ohms law: R = V / I = (12.0 - 2.0) / 0.02 = 500 ohms (Note: the voltage across the resistor is the battery voltage minus the voltage we want across the LED) But which value of power should the resistor be capable of handling? P = V x I = (12.0 - 2.0) / 0.02 = 0.2 WattsNote: k = x1,000 M = x1,000,000 G = x1,000,000,000So a 10k resistor = 10kohms = 10,000ohms
What does a 100k resistor do?
Resistance: Electrical resistance describes how an electrical conductor (a wire) opposes the flow of an electrical current (flow of electrons). To overcome this opposition a voltage (a energy) must dropped (used) across the conductor (wire). Resistance can be described by ohms law: Ohms Law: R = V / I (Resistance = Voltage / Current) (resistance measured in ohms) where: Voltage [V]= the energy lost across an component (voltage measured in volts). Current [I] = the charge (electrons) flowing through an component (current measured in Amps). Electrical resistance can be thought of as sticking your hand out a car window. The faster [current] you drive the harder the wind presses [resistance] against you hand and therefore it takes more energy [voltage] to hold your hand steady. When trying to overcome electrical resistance, the electrical energy lost is turned into heat. This is how the elements of a household stove, toaster, and fan heater work. Because of the vacuum in a light bulb, the electrical energy lost is instead turned into light. It can be seen the electrical resistance plays a large role in modern life. Resistor: The resistor is the most common electronic component and is used to limit and/or control the voltage and current in an electronic circuit. Resistors are carefully manufactured to provide a predetermined value of electrical resistance which may range from 0.1 ohms to 100,000,000 ohms, depending on the application. The physical size of a resistor also varies dependant on the amount of power passing through the resistor, given by: P = V x I (Power = Voltage x Current) (power measured in watts) There are also many types of resistors including: · Variable Resistor - changes resistance when its shaft is rotated (volume knob on a stereo). · Thermistor - changes resistance when the temperature changes (used in a thermostat). · Light Dependant Resistor (LDR) - changes resistance when the lighting changes (used in children's night-lights). Resistor Example: An LED is a small red light (such as the one on the front of most TVs) and requires 2.0 volts and 0.02 amps to operate correctly. If we connected that LED up directly to a 12 volt battery, the voltage would be too high, and too much current would flow… the LED would blow up. We need to use a resistor to limit the voltage and current. But which value of resistance should the have resistor? Uses ohms law: R = V / I = (12.0 - 2.0) / 0.02 = 500 ohms (Note: the voltage across the resistor is the battery voltage minus the voltage we want across the LED) But which value of power should the resistor be capable of handling? P = V x I = (12.0 - 2.0) / 0.02 = 0.2 WattsNote: k = x1,000 M = x1,000,000 G = x1,000,000,000So a 10k resistor = 10kohms = 10,000ohms
What do the bands on resistors mean?
in simple terms, band represent numbers, ex:- 10K resistor have different colour code and that is difference from 5k resistor. if you type in google 'resistor colour code' that will describe how to calculate a resistor value. thanks
What does v20 plus 10k mean?
If something has v20 plus 10k on it, it means that it is positive. This is typically used to describe something that has volts going through it, or electricity.
What are nominal values?
Nominal values are the values that a component is specified to be. For example, the nominal value of a 10K resistor is 10K. Its actual value may vary, though, based on its tolerance.
