What is the engine block code on a 1989 240sx se?

on the front of the engine to the right as you look at it. The engine block protrudes out past the head and on the top of this protrusion is stamped engine code and number. on the front of the engine to the right as you look at it. The engine block protrudes out past the head and on the top of this protrusion is stamped engine code and number.

its Chevy 454 Big Block Engine

the gsr engine will have a code on the block in plain view that reads b18c1 or b18c the h22 will have a similar code on the block but it reads h22

This is a warranty replacement engine. There are several decoders for the block numbers for these engine on the web and all require the block serial # as well as this code.

its the chassis code for 89-94 Nissan 240sx

The block casting numbers are on the top driver side of the bellhousing flange at the back of the engine. The engine code is stamped into a pad on the block deck in front of the passenger side cylinder head.

I'm not sure if there is really a engine color code on the engine, but there is a engine code. Look on the cylinder block close to where the transmission connects to. There should be a extended flat surface and the engine code should be imprinted on it. I'm pretty sure the engine code should d16z6 for an ex and si model, but on for 92-95

P0125: insufficient coolant temperature for closed loop fuel control you need an ECT sensor engine coolant temperature

Hi, This should be located on the engine plate which is normally on the engine block or on RH side of engine compartment. Kev

GMC code 32 - EGR system Its the system that puts exhaust back into your engine

Engine block is cast 2.2 or 2.5 under alternator . Vin also distinguishes engine . Eighth digit is engine code.

No Differences. s13 (1989-1994) and s14 (1995-1997?) just explains the chassis code. Through 1989 and 1997 the 240sx use a KA24DE motor. However, the 1989/1990 KA's were SOHC and the 1991+ were DOHC, so the only faster engines would be the 1991+ 240s compared to the 1989/1990

When the check engine light is on, the computer sets a fault code. Most auto parts stores will check this code for free and tell you how to fix it.

It's b16y8. It's on the front of the block.

b15 is the type of engine block that is in your honda

With an engine code D16A8 it's 1.6Ltr.

It is located on the side of the engine block. If you have a code for a knock sensor and you have a noise in the engine, it will set the code. That does not mean that the sensor is bad. They very rarely give problems.

you will need to compare the engine code stamped on the engine block, and then you will need a book/manual that will tell you if they are compatible or not.

On the engine block on the top front just behind the water pump on a machined surface the code will be stamped.

the eight digit of your v.i.n. number is the engine code The actual numbers are on the block at the back of the head mounting surface on the driver side.

LOOK UP THE ENGINE CODE STAMPED INTO THE FRONT LEFT (DRIVER'S SIDE) BLOCK BY THE HEAD.

The lower right hand fuse closest to the transmission tunnel is the fuse, if there is 1 in there already! then you are probly getting codes flashing all the time with engine running or not. IF code 12 ONLY with engine OFF just remove the fuse.

the key code for 1989 cadlillac

No, the 240sx is a rear wheel drive car and the transmission is completely different from the front wheel drive Altima. The engines themselfs are also set up differently even thought they both share the "KA24DE" engine code.

Open the hood and stand in front of the engine. On the front of the block on the passenger side you should find a two letter engine code. Cross reference that code against this web site. http://www.oldride.com/library/1963_pontiac_catalina.html