Best Answer

Firing order for a 6.5 CI single cylinder engine is In this order .. Cyl # 1 first .. than Cyl # 1 and than Cyl #1 I will let you guess what comes next .... It only has one cylinder ... thetr is no order for firing ... multi cylinder engines have firing orders ... :) Thanks Dave. This has been puzzling me for years but your explaination makes it all clear.

User Avatar

Wiki User

โˆ™ 2004-12-06 00:00:00
This answer is:
User Avatar
Study guides

Where I can purchase purchase HID Fargo ID card in Dubai

See all cards
No Reviews

Add your answer:

Earn +20 pts
Q: What is the firing order of a Briggs and Stratton 6 5 CI single cycle engine?
Write your answer...
Still have questions?
magnify glass
Related questions

Can you replace your 12.5 Briggs and stratton tractor engine with a 16hp Briggs and stratton?

Yes, most all of the Briggs single cylinder engines are exchangable. You just need to be concerned to make sure that you don't under power your mower. In your case that is not a problem.

What is the torque sequence for a 18hp single cylinder Briggs and stratton engine horazontal shaft head?

The torque sequence for a single cylinder Briggs and Stratton engine horizontal shaft head is increments of 2's for hp and 1's for head bolts. That makes 11 head bolts for an 18 hp.

How do you adjust valves on your Briggs and stratton lawnmower engine 18.0 ohv?

You do not state if it is a single or a twin (which it could be of either at that HP) so links to each below:

What are the three types of Briggs and stratton carburetors?

From the 1994 Briggs & Stratton Repair Manual - For Single Cylinder 4-Cycle Engines, it says the three styles are Flo-Jet carburetors, Pulsa-Jet carburetors and Vacu-Jet carburetors. Hope that helps.

How do you adjust valves on 16 hp Briggs stratton intek single cylinder motor?

Even though an Intek is not shown, it would be the YouTube video below.

What is the firing order for a 2003 Honda XR100R?

It is a single cylinder engine with one spark plug so there is no firing order.

Where do you find parts for an old Briggs Stratton 8 hp single cylinder engine with a serial 27065 model 14 type 202010?

If that is a cast iron engine its 5 horse, look up Smiths small engines in Google that's were I get all my old parts.AnswerI used to have this really old snapper rider that i had to reguild the engine on and I found parts through the local lawn mower shops and through online lawn mower parts sites. Hope this helps you. Call the Briggs and Stratton tech support line on You might even end up talking to me! I'm looking through a parts & repair manual for the model 14 as I type this...

How do you set valves on 18.5hp Briggs and stratton?

There's a dot stamped on a single tooth of the cam gear...There's also a dot stamped on a single tooth of the crank gear... Line 'em up and you're good to go...Valves are timed...Good luck...

How many hours will a 5000 watt generator run?

It depends on the load it is under, the size of the engine, who made the engine (Honda, Tecumseh, Briggs & Stratton, etc) and I'm sure many other factors. We have 3500 watt Honda generators at work that will run 12 hours on a 2.5 gallon tank under light load (a single power tool and/or battery charger).

Why would the 21 hp Briggs and stratton start running off one cylinder?

Most single cylinder failures on B&S twins are due to electrical failures. Check ignition diodes, coils, and key switch first.

How do you set the timing of the camshaft and the crankshaft properly on a Briggs and Stratton 7ohp Intek single cylinder OHV moter?

More than likely, there will be a dot on the gear on the crankshaft, and on the timing gear, and you just need to make sure that they line up.

What is the Valve clearance Briggs 18 HP single cylinder intek engine?

turn engine to top dead center on compression stroke then turn 1 quarter of an inch passed set at .005

People also asked