answersLogoWhite

0


Best Answer

look up the engine cylinder numbers, then look at the front of your engine, or on the intake manifold. There will be a series of raised numbers, (you may have to clean off some grease), this is your timing order. Make sure you have the correct sparkplug wires going to the correct plug from your distributor.(make sure your distributor is mounted correctly) Jody

User Avatar

Wiki User

โˆ™ 2006-03-26 18:54:58
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: What is the ignition timing on a 1990 Ford Probe v6?
Write your answer...
Submit
Related questions

What is Ignition timing 1990 Ford Probe 2.2?

motorcraft.com shows for the 1990 Ford Probe 2.2 L ( 133 cubic inch ) 4 cylinder : ignition timing : 6 degrees BTDC , and --------------------------------------------------------------------------------------------------------- 9 degrees BTDC - manual transmission - with turbo - with self test connector grounded


How do you set ignition timing on a 1989 ford probe?

where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top


How do you set the ignition timing on a ford probe gt 95 with an mx engine?

To set the ignition timing on a Ford Probe GT 95 with an MX engine, remove the two 12 mm head bolts holding the distributor in place. Then rotate the distributor to set the ignition timing.


How do you set ignition timing on a 1995 Ford Probe?

there are two dots on the distributor they have to be lined up on tdc


Where is the dura spark ignition module located on a 1991 Ford probe?

The 1991 Ford Probe spark ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


How do you by pass the alarm on a 1990 Ford Probe?

The nosiey engine in ford 1990 how can we overcome it?


Why does Ford Probe ignition stays on even when key is not in ignition?

Defective ignition switch or tumbler assembly.


How do you time a 360 ford?

Ignition timing or valve timing?


1990 Ford Probe distributor?

What is your question?


How do you change the timing belt on a 1990 Ford engine?

From my research, as an owner of a 1990 Ford Tempo GL, there is no timing belt.


Where is the ignition coil in a 1995 ford probe gt?

Built into the distributor.


Where are the timing marks on a 93 Ford Probe?

They are on the camshaft and crankshaft sprockets


Can you adjust ignition timing on a 98 Ford Ranger 3.0 liter?

Yes ANSWER No - a 1998 3.0 L Ford Ranger does not have a distributor which would allow you to adjust the ignition timing - it has a coil pack and the ignition timing is controlled by the PCM ( powertrain control module )


Ignition timing for 1978 Ford 351m?

point gap 1978m ford


How do you sit timing on 2.0 Ford Contour?

The ignition timing is controlled by the ECU, and is not adjustable.


How do you check the timing on a 97 Ford Contour?

The ignition timing is controlled by the ECU, and is not adjustable.


How do SET timing on a 1998 ford contour se?

Ignition timing is automatically set. sorry.


Does a 1990 Ford Tempo GL have a timing belt?

it should have a timing chain


Does a 1990 Ford Ranger 2.9 have a timing chain or belt?

The 2.9 liter V6 engine in a 1990 Ford Ranger has a timing CHAIN


Can you adjust the ignition timing on a 1994 Ford Ranger 3.0?

if it has a distributor you can.


Speedometer 90 Ford Probe?

You can find a speedometer for a 1990 Ford Probe online at places like Ebay or Amazon. You can also find this speedometer at Rock Auto on the Internet.


What is the ignition timing for 1970 mustang 302 engine?

The ignition timing for a 1970 Ford Mustang with 302 - V8 - 2 barrel carburetor is : ( 6 degrees BTDC )


What the timing set at on a 1991 ford ranger 2.8 liter?

If you mean ignition timing it will be 10 degrees BTC.


What are the timing specs for a 2.3 1989 ford ranger?

The ignition timing is computer controlled - not adjustable - but the base timing is 10 degrees BTDC


What is the ignition timing for a Ford 2.3L LSG-4231-6005-A?

The firing order is 1-3-4-2 and the distributor rotation is clockwise. The timing is 10 degrees before top dead center for 1985 to 1990 models.