answersLogoWhite

0


Best Answer
Copy

timming just needs to be close the computer adjusts it to what it needs and the points are gone since the early 70's it is electronic with moduales, sensors and such

User Avatar

Wiki User

โˆ™ 2006-12-29 14:58:19
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: What is the ignition timing spec and what is the ignition point dwell or point gap spec for a 1989 Dodge PowerRam 50 4X4 pickup?
Write your answer...
Submit

Related Questions

How do you replace the ignition timing on a 1987 Dodge Ram 350?

the ignition timing does not get replaced on 87 dodge.


Dodge pickup with a 1960-72 slant six that wont start but it does back fire int to the carburetor?

Check ignition timing Timing chain "jumped"?


Does your 04 Dodge pickup have a timing belt?

No, all truck engines have timing chains.


What the correct timing mark for a 1990 dodge ram 318?

whats the correct timing mark for a 1990 dodge ram pickup 318


What is the ignition timing for 1986 dodge truck 5.9 360?

I did not get a answer


Does a 2001 dodge Dakota sport pickup have a timing chain?

Yes it does.


Ignition timing 1977 dodge pickup 318?

18436572 is the order. potentially the harmonic balancer should have a carved notch which lines up with the timing mark on the block somehow The degrees should be on a label under the hood.


Where is the Location of ignition control module Dodge ram pickup 1500?

in the computer


What is the ignition timing on a 1980 dodge D50 Pick UP?

The ignition timing on a 1980 Dodge D50 Pickup is: 2.0 L engine: 5 degrees BTDC 2.6 L engine: 7 degrees BTDC Additional info FYI: #1 cylinder location: FRONT Distributor rotation: CLOCKWISE Firing order: 1 - 3 - 4 - 2


What is the ignition timing spec for a 94 dodge b250 van 3.9L?

Timing is handled by the computer, there is no adjustment needed.


Does my 2004 Dodge Ram Pickup 1500 have a timing chain?

Yes it has 3 if it is a 4.7


What is the ignition timing on 1990 dodge 250 van?

I believe it is - 1,8,4,3,6,5,7,2 on a V8


Dodge Ignition pickup circuit to reluctor gap?

Depends on year usually .06 to .08


Where do you find ignition module on 1996 dodge Ram d50 mini pickup?

incorparated in the pcm


What would cause a 1988 dodge d100 ignition not to fire?

change the pickup coil in distr


Distributor timing for 2000 dodge 3.9?

Ignition timing for 2000 Dodge 3.9L engine is set and maintained automatically by the engine's electronic control module and is not possible to change.


Why will the ignition not turn off on a 1977 Dodge pickup?

It could be the keyswitch or the starter could be wired wrong.


How do you set the ignition timing on a 2000 Dodge Durango 5.2?

The distributor is synched or zeroed with the scan tool. It can not be done with a timing light.


What would make your 97 dodge ram 1500 pickup kills when you put it in gear?

it could be your timing.


What causes a Dodge to back fire?

Ignition timing, spark plug or wire, internal engine,


Do you know the ignition timing for a 1966 Dodge Dart?

Get a chiltons repair manual from the library for your car.


How do you set the ignition timing on a 1994 dodge ram 360?

The distributor is synched to zero degrees with a scan tool. It can not be done with a timing light.


How do you set the ignition timing on a 1993 dodge 3.9 v6?

Initial timing is set by lining the rotor up with the mark on the pickup plate in the distributor with the crankshaft at #1 top dead center. The timing is then fine tuned to 0 degrees with a scan tool. It can not be done with a timing light.Initial timing is set by lining the rotor up with the mark on the pickup plate in the distributor with the crankshaft at #1 top dead center. The timing is then fine tuned to 0 degrees with a scan tool. It can not be done with a timing light.


What is the ignition timing setting for a 1997 dodge ram 5.9l?

The 1997 dodge ram doesn't have adjuastable timing if the. The timing is controled by a crankshaft sensor near the transmission bell housing and a cam position sensor in the distributor. the cam position sensor is uned mostly for fuel injection syncronization. The crankshaft position sensor mainly controls ignition timing and is not moveable/adjustable.


How do you remove and replace ignition switch 1983 Dodge D150 pickup?

You have to remove it gently and go to auto zone and turn it in