Chevy Malibu
Air Filters and Intake Manifolds
Grand Am GT

What is the labor cost of replacing the manifold gasket on a 1998 Chevy Malibu?

353637

Top Answer
User Avatar
Wiki User
Answered
2005-04-24 02:17:50
2005-04-24 02:17:50

Intake manifold or exhaust? The complete job (parts and labor) is between $700-$900. depending on labor rates.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The head gasket on a 1999 Chevy Malibu is replaced by removing the coolant, intake manifold, and retaining bolts. The cylinder head can then be removed, the gasket replaced, and everything reassembled.

I'm sorry but i actually have a 99 Malibu and they do have a intake manifold gasket which are commonly mistaken for a head gasket when it blows. Mailbu's 97 to 2000 are bad for them blowing. it is located on top of the engine. it's still very expensive **tamnesha Some Chevy engines of that period didn't have a gasket; just a thin film of sealant.

Remove the intake manifold retaining bolts from your 1996 Chevy Astro Van. Remove the manifold gasket and clean the surface. Reverse the process to install the new intake manifold gasket.

You will need to remove the exhaust manifold retaining bolts in your 1993 Chevy Astro. Remove the exhaust manifold. Remove the exhaust manifold gasket and clean the surface. Reverse the process to install the new exhaust manifold gasket.

The Chevy Cruze and the Chevy Malibu

is their a web site, that will provide me with the a print out for the intstalling of a intake manifold gasket for a 2003 chevy aenture.

Assuming this is a 4.3L engine, the upper intake manifold gasket would be between the upper intake manifold and the lower intake manifold.

No, You don't put anything on Head, Exahust or intake gaskets. CJ actually you do put a 1/8'th inch bead of black silicone on the gasket to ensure no leaks occur and it also helps hold the gasket in place when your putting the intake manifold on. I'm a ford master technician, you ALWAYS use silicone when replacing intake and head gaskets. =DK

what are the signs for replacing the oil gasket in a 1996 Chevy cavalier

where is the location of tensioner of 2002 3.1 L Chevy Malibu to adjust if replacing the alternator?

there is no lower intake gasket, only a front and rear gasket

If the exhaust manifold gasket is leaking the only fix is to replace it with a new one.

You need the sealant on the ends where the supplied gaskets don't cover fully.

5 hours labor Book time. A good experenced mechanic can do it in about 3 hours.

go to a parts store and get a haynes manual for your car year and model!! it will describe what to do step by step!! Just did mine!!

They only Head Gasket I had to replace was on a Chevy Malibu 1999. Cost me about $1400

If you are sure that it did not freeze and crack the block, Then the intake manifold gasket is leaking. That is a common problem with the vortec Chevy engines. You need to replace the gasket with a factory Chevy gasket from the dealer.

The Lower Intake Manifold gasket. Do a search on that in Google, the Chevy Malibu and the Pontiac Grand Am and the Alero all have the same motor with the same problem. Yay!

where is the tensioner of 2002 3.1 l Chevy Malibu to adjust so that i can remove the belt when replacing the alternator?

there is no upper intake gasket, only a front and rear

Yes, the exhaust manifold on a 99 Chevy S10 2.2 will need to be be removed during the blown head gasket repair.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.