0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Name a simple machine that starts with t?
a simple machine that starts with t is a tap, such as a water tap. the lever which you use to open and close the tap is what makes it a simple mahcine.
What is foot lever?
A foot lever is a lever that is operated with the foot.
Lever?
The function of a lever is used to move or lift objects.
What is meant by the fulcrum in a lever?
A fulcrum is a point at which the lever is supported or about which the lever turns.
Which class lever beam balance?
first class lever
How can you convert a washer tap to a lever tap?
Buy a new tap.
What country uses single lever kitchen mixer tap-ware?
we have it in Australia...
Name a simple machine that starts with t?
a simple machine that starts with t is a tap, such as a water tap. the lever which you use to open and close the tap is what makes it a simple mahcine.
What is the main role of a tap handle?
Tap handles are pulled to deliver liquid from a tap. This is mainly used for beer and sodas such as root beer. They originated when alcoholic beverages were kept in wooden kegs or barrels. The tap system was activated by pulling the tap lever to get the liquid out.
When you let water into a bathtub what kind of machine helps you open the tap?
It depends on the faucet but generally it would be a screw or lever.
What you let water into a bathtub what kind of machine helps you open the tap?
It depends on the faucet but generally it would be a screw or lever.
How do you go back to neutral from high gear on a motorcycle?
Pull the clutch lever and downshift until the bike is in neutral. When the clutch is engaged it's just like neutral =================== a>clutch b>tap tap tap tap tap down on the lever. as many times as you want. You likely will feel it once it is in 1st. c> tap UP half a step It should feel light, not like a full gear change. Your neutral indicator light will light up if you have one. d> let go of the clutch slowly. Always slowly, just in case you left it in gear. If you did, then you can pull it back before you start moving.
Water from bath tap is lukewarm but hot from rest of taps?
Need to adjust temperature limit stop on faucet behind handle, on single lever valve.
How do you repair leek on single lever monobloc mixer tap?
Depends on the leak.Do NOT forget to close main water tap or safety taps before disassembling any tap.If the tap keeps dripping on the "spout" even when it is off then it is a problem with the mono bloc cartridge that controls water flow. It can be replaced by removing the lever (is is usually press fitted) and unscrewing the top of the tap. The cartridge should be exposed and easily removable. A new, compatible cartridge is inserted and secured.If it is a rotating "spout" and the leak occurs at the rotating base of the "spout". In this case the tap is disassembled and there should be 2-4 O rings keeping the water in. These need replacement. Some have metallic O rings that are very difficult to install. Lime can damage these O rings and usually builds near the edge of the base of the "spout" that rotates and the rest of the tap. To complete disassemble the tap remove lever, unscrew the top of the tap, remove the metal pipe that is between the top and the ring part of the "spout". The "spout" should slide up revealing the o rings.Connections to the tap could also leak. Flexible tubes can be unscrewed using a small wrench and have 1-2 rubber O rings that can be replaced The taps fixed directly on the pipes have rubber washers. To replace these you need to remove the tap by using a wrench and unfasten the nuts holding the tap to the pipes. The rubber washers are between the pipe and tap. After replacing the washers do not overtighten the nuts as you could damage the new washers.You could always replace the tap.
How do you fix twin lever monobloc kitchen tap?
You dismantle it from the top (handle first) then screw off the cover to see what is wrong. You can possibly get a repair kit in HD.
How do you remove the drive shaft from a 51 reg corsa?
just pull it hard out the box. If it won't come pull it and try to give it a tap out or lever it at the same time.
How old webley mk3 supertarget?
The Mk3 supertarget was made between 1946 and 1975. If it has Parker Hale sights and a nicely shaped and checkered loading tap lever its an early one. If it has a plain loading tap lever and PH sights its in the middle and the later ones had Anschutz sights, and no brass box on the pistol grip to hold PH inserts. It is difficult to be more precise from serial numbers as there is not the logical sequence found on some other makes.
