0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the voltage used for megger check of aircraft looms?
I did them with a 1,000 volt megger .
How do you test a 6 wire motor for insulation grounds?
You use a device called a megger or meg ohm meter. Have the voltage range of the megger set to the working voltage of the motor. The first test should be to ground. One lead on the frame of the motor , the other lead one of the 6 wires. Test all 6 wires. If no ground shows up, test the individual coils against one another. If the coils are not grounded together, the motor is safe to energize.
How can measure the voltage only seeing the insulators in a high voltage transmission lines?
i think 11kv per insulator
How megger produce voltage?
The megger is used to find insulation resistance in any equipement. It will generate around 10kVA power to test.
What is the required resistance in mega ohm when performing megger?
Normally the megger should be selected based on the following criteria. 1.Voltage rating of the megger 2.Range of the megger value 3.Manual - Hand operated analogue type 4.Auto- Digital Megger To measure the insualtion resistance of Motor (LV Motors) Up to 500 V/1000 V Megger is sufficient To measure the insualtion resistance of Motor (HV Motors) Up to 5000 V can be choosen Normaly the range starts from 0.5 to Infinity meg value in the analogue However in digital the based on the least count /range of the instrument we can able to measure the insualtion value.
How do you test motor for burn?
To test a motor, use a megger (megohm meter) to test the insulation of the internal motor windings. Select a voltage to apply to the motor using an output from the megger that is higher that the operating voltage that the motor operates on.
How do you check a motor for a bad winding?
You need a Megger tester. With one lead attached to the winding and the other attached to the motor housing, the Megger sends a high voltage through the winding. The Megger reads the resistance, letting you know if there is a short to ground.
What is the output voltage of megger is it ac or DC?
megger are available in ac &dc
What is the voltage used for megger check of aircraft looms?
I did them with a 1,000 volt megger .
What is the optimum insulation resistance for 11kV UGcables when tested by 5000v insulation megger?
High voltage cables with this high an insulation factor are usually given a Hi Pot (High Potential) test and not meggered. The potential has to be higher that the working voltage of the cable to be effective when checking for insulation or connector breakdown.
How do you use a meggar?
A megger is used to test the resistance of high voltage cables, insulation and motor windings. The test employs a megohm meter.
Why is high voltage from 11kv onwards?
To be precise this kind of hi voltage is called distribution by power company. 11kv 16 kv that type of voltage. however transmission can be in the range of 5ookv. And you can see at tower from interstates lines
What kind of tests is a megger used for?
A megger is an instrument that generates a high voltage. That high voltage is then used for measuring insulation resistance, especially that of electrical devices.
How do you test a 6 wire motor for insulation grounds?
You use a device called a megger or meg ohm meter. Have the voltage range of the megger set to the working voltage of the motor. The first test should be to ground. One lead on the frame of the motor , the other lead one of the 6 wires. Test all 6 wires. If no ground shows up, test the individual coils against one another. If the coils are not grounded together, the motor is safe to energize.
How can measure the voltage only seeing the insulators in a high voltage transmission lines?
i think 11kv per insulator
What type of voltage applied during megger test?
DC
What is the output voltage of an insulation tester which is required to test a 230v circuit?
On a hand crank megger which is used to test insulation breakdown, use the 300V setting. If the megger does not have that setting use 500V as opposed to 1000V for the test. The output of the megger is a DC voltage.
