0
What is the name of the song by The New Christy Minstrels with the verse I keep my pant's up with a piece of twine?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How long is a piece of twine?
The length of a piece of rope is twice the distance from the middle to one end.
Did slaves have belts?
No they had twine which they made into belts and tied around their waists to hold up their breeches.(pants)
How do you thread international 430 hay baler?
Twine comes out of the twine box, through the tensioner, through a couple of ceramic rings then 1 piece of twine through each needle eye. Once through the needle eye it goes back along the chamber floor and tie it off to something sturdy. The baler will thread the twine into the knotters at the first cycle. A common problem on old balers is the needle eyes have grooves warn in them. You should use a round file to file out the groove so the twine has a smooth surface to run over. A rough surface will cut the twine.
Easy diy twine rug?
Diy twine rugs are easy crafts that you can make out of twine by braiding.
Where does twine come from?
Twine is made from both plants and synthetic fibers. The two products are mixed to together to make the final twine product.
How do you use twine as a sentence?
I used twine to help my dad.
How do you get twine on FarmVille?
The collectible twine can be found when harvesting sheep on your farm.
Where is the object twine located in sims 2 castaway?
Twine is not an object or a plant. You find sisal first, then you make twine on a crafting bench.
Is twine recyclable?
If the twine is made from a natural fiber, like hemp, sisal or even cotton, then it is biodegradable.Some twine is made of plastic. This is not biodegradable.
What has the author F Twine written?
F. Twine has written: 'Low pay in Scotland'
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
A sentence with the word twine?
he used the only twine he had to tie the pieces of wood together for a raft.
