0
Grip it with your right hand and pull up (not too much) while pulling out. Make sure it is off first.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Why does a 3 pin plug have a clamp on it?
A 3 pin plug has a clamp on it to stop the wires from being ripped out of the plug when people use the wire to remove a plug from the wall instead of gripping the plug and removing it the proper way.
How do you remove the driver's side seat in a 2001 Mazda Protege?
Most likely the same way you remove any bucket seat in a car. 4 bolts holding the seat rails to the bottom of the car, and if it's an electrical seat, an electrical wire plug.
Can you use a 7 way plug on a 4 way plug to hook up a trailer?
With the proper adapter, yes.
How do you remove seat off 2003 Oldsmobile Aurora?
Move the seat all the way forward then remove the nuts or bolts from rear. Move the seat all the way back then remove the front nuts or bolts. Tip the seat back and disconnect the electrical plug(s). Remove the seat from vehicle.
How do you remove the spark plugs from a 2001 Mercury Grande Marquis?
You should have C.O.P. ( coil on plug ). Just remove the coil, and remove the plug the normal way.
Where is the daewoo matiz radiator drain plug?
The radiator does not have a drain plug. The easiest way to drain is remove a hose.
Which way does the oil drain plug turn to remove it on 2003 Ford Focus?
lefty loosy,righty tighty.turn it to the left to loosen the drain plug. to remove 2oo3 focus drain plug turn drain plug counter clockwise that is to your left '
Which way do you turn oil plug to remove it from a 2003 Chrysler town and country minivan?
The drain plug is turned counter clockwise to remove it on a 2003 Chrysler Town and Country.
How do you unflood a scooter engine?
The way you unflood a scooter enging is really the same as most engines. First you remove the spark plug. Second, If the spark plug dose hase gas on ether burn it off or find a way to remove the gas for the spak plug cilender.
How do you change the spark plugs on the kawasaki vulcan 900 classic LT?
Remove the spark plug wire on the right side of the motorcycle. It's at the top of the motor, at the front of the fuel tank. You will need a special spark plug socket to remove the spark plug. Wherever you get the new spark plug's, they can get you the correct wrench. Put a 3 inch extension on the socket, It should go all the way down to the spark plug, and have just enough room to get you're drive ratchet on it to remove the spark plug. When you have screwed the spark plug all the way loose, You will need to remove the ratchet to pull the extension out with the socket, and the spark plug in the end of the socket. There should just be enough room to remove it. I had to remove a breather hose at the bottom of the fuel tank to fully remove it. Put the new plug in, Make sure it is secured in the socked, Mine dropped, and when I retrieved It, It had messed up the gap setting. The other one is on the other side at the rear of the fuel tank. You will need to remove the two bolt's at the bottom of the tank, and pull up on the tank, and prop it up with a WD-40 can so you can get the proper clearance to remove the second one. I found it easier to remove than the other one. There was no hose to remove.
Subaru Outback Power Steering Pump Replacement?
The following is for the 3.0L H6: Remove the "V" Belt. Drain the Radiator so that the coolant level is below the Upper Radiator Hose. Remove the Clamps, remove the Hose from the Radiator & rotate the Hose counterclockwise out of the way. Empty the Pump Reservoir. Remove the Pump Hose Fittings & disconnect the Electrical Plug. Remove the three 14 mm bolts holding the Pump Bracket & the 12 mm bolt holding the Generator. Remove Assembly & replace Pump. Installation is reverse. Refill the Pump Reservoir & the Radiator with the proper fluids & quantities.....
What is the proper way to change a radiator that has a transmission cooler?
If you can unbolt the cooler then unbolt it whatever way is easiest. Then remove the radiator. If it is part of the radiator itself then drain the radiator first completely and then disconnect the tranny lines and try to plug them if possible or put then draining into a container. Dont want to mix the fluids. Then remove the radiator. That should be it. That is way that I have done it before.
