Fuel and Engines
Chevy S-10
Ford Ranger XLT
Windmills

What is the purpose of the crank shaft?

383940

Top Answer
User Avatar
Wiki User
2005-02-20 03:02:47
2005-02-20 03:02:47

The crankshaft is an internal component of the engine that converts an up and down movement of the pistons to a rotational movement of the the crankshaft. This is provided to the powertrain for movement. The bottom of the pistons are attached to the crankshaft with main bearings.

123
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

I would recommend that you do put a crank shaft head on a crank shaft. Putting any other type of head on a crank shaft could possibly break the head.

User Avatar

The engine crank shaft is inside the engine

User Avatar

The crank sensor on a 2001 Malibu is located on the bottom of the engine near the crank shaft. It monitors the rotation and speed of the crank shaft.

User Avatar

Where is the crank shaft sensor located in a Audi a6

User Avatar

2 types of crank shaft are there 1.same plane 2.cross plane crank shaft in cross plane crank shaft cranks are inclined at 90 degree and in same plane crank shaft cranks are in same plane. thnk u

User Avatar

how to get the crank shaft pulley off of a 03 Hyundai elanta GLS

User Avatar

One symptom of a bad crank shaft sensor is the car having trouble starting. The car stalling and backfiring are other symptoms of a bad crank shaft sensor.

User Avatar

A video instruction guide on how to check a crank shaft pulley can be seen on YouTube. Just type in "How to check crank shaft pulley", click on Search, then play the first video.

User Avatar

The crank shaft sensor on a 2000 Chevy Suburban is located on the bottom of the engine, near the oil filter. It constantly monitors the crank shaft and updates the vehicle's computer of its status.

User Avatar

A round piece of pipe, that fits over the crank snout, and a big hammer.

User Avatar

To remove a crank shaft pulley you need to first jack up the car. Next, remove the bold holding the crack shaft pulley in place and remove the unit. Reverse direction to put the new crank shaft pulley on your car.

User Avatar

How do you replace crank shaft sensor on 2005 Chrysler 2005 300c?

User Avatar

install 3.8 Chevy impala crank sensor passenger side , remove wheel and use pully to pull out crank shaft

User Avatar

The crank shaft positioning sensor is behind the starter. A real bear to get to.

User Avatar

YES ON ANY VECHICLE THE CRANK SHAFT SEAL CAN FAIL WITHOUT WARNING.

User Avatar

AnswerCheck the crank pully bolt. If it has come loose you will have a leak.The crank pully bolt does not have anything to do with the crank shaft seal leak. Thebolt is independent of the seal. To replace seal remove crank shaft pully and you will have access to crank shaft seal, pull out & replace seal.

User Avatar

the portion of a crank between the crankpin and the shaft or between adjacent crankpins -called also crank arm, crank throw

User Avatar

the purpose of the hair shaft is to protect and moisturize the scalp.

User Avatar

trying to locate crank shaft sencor for 1993 Chevy lumna trying to locate crank shaft sencor for 1993 Chevy lumna

User Avatar

the crank sensor is located just behind the crank shaft pully of the engine.

User Avatar

crank shaft sensor is near the oil filter. I have the repair manual but I am unable to past the page in here.

User Avatar

a 3 piece ( the best type of crank) can be 60$ and up

User Avatar

That year model does not have a crank sensor.

User Avatar

its under crank shaft hub. hope its helps.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.