0
What is the purpose of the mast latch and knob assembly on the TF-2 Flood light?
Wiki User
∙ 11y ago
Locks the mast in the vertical position.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the purpose of the light bulb stem?
It is used to support the filament assembly.
How do you replace tail lights 2003 impala?
Open the trunk. Loosen the black thumb latch wing nuts that hold the tail light assembly in place. pull the tail light assembly out. You should be able to acces the tail light bulbs to replace them.
Where is trunk light switch for Pontiac Sunfire?
The trunk light switch on a Pontiac Sun Fire is typically in the latch assembly. This is usually inside the trunk and under the carpet.
Why would a 1995 Ford Ranger give a long beep and the dome light come on?
Your door latch is not functioning properly or your "Door Ajar" switch isn't functioning. Try WD40 in the door latch. If that doesn't work, you may have to remove the latch assembly and clean it, then work it manually for a while my ranger took about 30 minutes to free up the latch spring.
Change ashtray light in 2001 windstar lx?
I just changed the ashtray light in my 2000 Windstar LX. It is probably similar. Open the ashtray. Take a regular screwdriver and insert it between the top of the ashtray and the dash board in the center of the ashtray. There is a latch hidden there. Lift the screwdriver handle, which will press down on the latch. Then simply pull out the ashtray. It will be connected by the wires for the light. You can either disconnect the wires or carefully turn over the ashtray. When you turn it over you will see the light assembly attached to the wires. It snaps out of the ashtray. Then you can remove the light from the assembly by releasing the latches of both sides of the assembly. Then the light pulls straight out. Putting it back together is a little tricky. Once you have the new light installed and the light assembly put back together you need to reinstall the light assembly. This is a bit of trouble. Perhaps putting a piece of scotch tape around the assembly will help to get it aligned. It snaps back into place. Reconnect the wires if necessary and reinsert the ashtray.
What is the best type of reverse light to use spot or flood light?
flood.
2000 jetta gls replaced bulb in trunk and it does not work none of the fuses look blown. New bulbs from 3 separate vendors none worked.?
I had this problem once on my 2000 jetta. When I took it into the shop, they told me that the latch assembly was at fault. Once replaced, I had light in the trunk again. So, my guess is that the light switch part of the latch is faulty and not turning on the light.
1996 explorer - the red - door open - dash light stays on. put carb cleaner - w-d 40'd the latch. is there a switch in the door latch assembly or is it a relay problem somewhere else?
The door ajar switches are inside the doors mounted on the door latches.
What is the difference between a narrow flood light and a spot light?
A "spot" is more narrow than a "narrow flood".
Is 480 lumens good for flood light?
No. 480 lumens is about the output of a 40 watt light bulb, and that will not make a very good flood light.
Location rear door light swicth 1996 gran marq?
i believe it is located somewhere in the door hinge assembly ---- The switch for the interior lights is located inside the door latch. See link below.
How do you replace rear latch release switch on a rendezvous?
You have to take the trim panel off of the inside of the tailgate. Not just the removable section across the middle, but the whole thing. There are a series of screws that hold the tail light assembly to the back of the tailgate. You need to undo all of the nuts on the inside to release the tail light assembly, and be sure to unplug the harness as you remove it. The pressure switch is bolted behind the tail light assembly. Once you have the assembly out of the way, just fish the plug for the switch down and out with the switch. Change the switch and put it all back together.
