0
web search suggests 1.0mm
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is plug under corsa radio console?
I think it might be the OBD (Diagnosis) Port.
Why does your Mazda B 2500 not start when it rains even when it is under a car port?
It doesn't matter if the vehicle is under a car port or not, the humidity is high and if the spark plug wires are bad it won't start. Replace the spark plug wires.
You have a 1997 suzuki esteem and you noticed a spark plug was drenched in motor oil what would cause that?
replace valve cover gasket. there are 4 small rings that seal the plug ports. this keeps oil out of the spark plug port.
How do you change the spark plugs on a 1989 Chevy Celebrity 2.8 multi port?
To replace spark plugs: 1. Remove the spark plug wire. Twist the boot to free it up from the spark plug, then pull the wire off with the boot. 2. Use a 5/8" spark plug socket with suitable extension and either a ratchet or breaker bar to loosen the spar plug and take it out. 3. Set the gap on the new spark plug to 0.045" and use the spark plug socket to install it. 4. Reattach the spark plug wire and move to the next spark plug. I do them one at a time, that way I don't get them mixed up. Now may be a good time to replace the spark plug wires.
Where is the low side port located on a LS400?
Low side port for A/C is located on passenger side to the back of engine. about where the second spark plug forward
Why is there a puddle of oil down in the spark plug port on my 1998 dodge stratus?
Could be a leaking valve cover gasket
What can you do when you have a misfire in one of your engines cylinders?
You need compression, spark and fuel. The misfire cylinder is missing one of those. Do a compression test to see if the valves and rings are okay, all cyinders should be within 10% of each other. Pull the spark plug out of the suspected cylinder, if the plug is wet it probably does not have spark. If the plug is dry it probably is not getting fuel (port injected engine).
Where is the location of the diagnostic port on the 1995 Isuzu rodeo?
The diagnostic port on a 1995 Isuzu Rodeo drive is located on the lower kick panel on the driver's side. It is just below the left spark plug.
How can one install a combo drive?
This computer technology works on 'master and slave' technology. in this two similar type of devices can be attached to the same data port on the motherboard. In order to install a combo drive there are two possible conditions:-1. you already have a CD-ROM,CD-rw etc.2. this is your first drive. if you already have drive then plug the data cable of combo drive into the previous drive and then plug the power cable of combo drive drive into power supply of system . then turn on the system combo drive will appear as the slave of previous drive . The combo drive is ready to use. (In case of an OS other than win- xp, you are supposed to install a driver). If this is your first drive then plug the data cable of combo drive on the motherboard and plug the power supply and turn on the system drive will appear (in case of OS other than win- xp, you are supposed to insall a driver).
Where is the Diagnostic Port on a Vauxhall Corsa sting 1997?
Under the heater controls
Can port allow you to plug hardware into your CPU?
A port allows you to plug hardware into your CPU.
How do you change spark plugs in a Saab 93 Arc?
These instructions are for the 2.3 Liter 4 cylinder turbo engine, not the V-6. First of all, Set aside some time Make sure you have the best spark plugs Suggestion: Change your spark plug wires at the same time. Instructions on how to do this are not provided Tools you'll need: Socket wrench Extension for your socket wrench Spark plug socket Step 1. Unhook the spark plug wires from the spark plugs. Make sure you recall which wire you are taking off and where it goes so you'll be able to reattach it. If you have to mark each wire with numbered tape. Step 2. Loosen your 4 spark plugs using your socket wrench, socket wrench extension and spark plug socket. When loosening be gentle and don't make any sudden rapid movements. Unscrew until you are able to pull the socket wrench slowly out of the spark plug hole with the spark plug attached. Repeat step until each spark plug is removed. Step 3. Place a spark plug in the in the spark socket with the pointy end facing into the engine. Then slowly screw in a spark plug into a spark plug hole. Keeping on screwing until you begin to feel resistence. Once you do make about 3 to 4 more turns if you can, but DO NOT over tighten. Make sure the spark plugs are not extremely tight. *As a guage for tightness just recall how tight the spark plugs were before you loosened them.* Continue this step until each spark plug is inserted in its engine port/hole. Step 4. Reattach the spark plug wires to each spark plug just as they were attached before you loosened them Procedure is complete.
