0
What is the torque sequence and torque for head bolts on a 1992 Toyota Paseo?
Wiki User
∙ 15y ago
you need a chiltons motor guide don't count on what someone on the computer tells you ..this has to be right or you just wasted a lot of money
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the cylinder head torque on a Toyota Paseo?
The cylinder head on a Toyota Paseo requires 33 pounds of torque on the head bolts. If the bolts are over tighten the block can warp leading to a blown head gasket.
Torque settings for citroen saxo cylinder head bolts?
in sequence torque bolts to 20nm, then again in sequence turn a futher 120 degrees, and again in sequence 120 degrees.
What is the torque specification for Toyota Camry 1989 four cylinder head bolts?
1991 toyota camry head bolts torque specs
What is the torque rating for the head bolt on 93 subaru 1.8 4 cylinder engine?
NOTEStep 1: Tighten all bolts to 22 ft. lbs.Step 2: Tighten all bolts to 51 ft. lbs.Step 3: Loosen all bolts, in reverse torque sequence, by 180°Step 4: Loosen all bolts, in reverse torque sequence again by 180°Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs.Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs.Step 7: Tighten all bolts, in torque sequence, by 80-90°Step 8: Tighten all bolts, in torque sequence, again by 80-90°
Subaru 2.2 Head torque specifications?
{| |- | NOTE Step 1: Tighten all bolts to 22 ft. lbs. Step 2: Tighten all bolts to 51 ft. lbs. Step 3: Loosen all bolts, in reverse torque sequence, by 180° Step 4: Loosen all bolts, in reverse torque sequence again by 180° Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs. Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs. Step 7: Tighten all bolts, in torque sequence, by 80-90° Step 8: Tighten all bolts, in torque sequence, again by 80-90° |}
What is the torque sequence for rocker arm bolts on a 1991 ford 1.9 engine?
There is no torque sequence just torque rocker arm studs to the proper torque
What are the torque specs and pattern on the head bolts of a 1991 Toyota pickup with the 3.0?
The torque specs and pattern on the head bolts of a 1991 Toyota pickup with a 3.0 engine are 5, 4, 6, 3, 2, 7, 1, and 8. This sequence is started from the center of the head and requires 75 foot pounds of torque on each bolt.
How much is the torque of 2c cylinder head bolts Toyota?
torque for 2c engine cylinder head bolts
What is the torque of cylinder head Toyota 2c diesel turbo?
What is headcylinder bolts torque on toyota 2c turbo
1995 Mercury Tracer Torque specs for head bolts?
Torque sequence------------ l 93157 l l 862410 l ------------ Step 1: torque in sequence to 44 Ft/LBS Step 2: in sequence completely loosen all bolts Step : retorque all bolts in sequence to 44 Ft/LBS Step 4: in sequence turn an additional 90 degrees Step 5: in sequence turn an additional 90 degrees Recheck final torque in sequence***CAUTION*** engine uses Torque To yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.
What is Toyota Camry cylinder head bolts torque specs?
The torque specs for a Toyota Camry cylinder head is 60 pounds for the inside bolts and 50 pounds for the site bolts. The cylinder head bolts should be tight from and to end alternating.
Torque specs and sequence for head bolts for 1993 3.8 ford?
For my Mercury Cougar with Aluminum Heads it is:Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket be sure to replace all torque-to-yield style Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com
