0
What is the value of resistance between the leads of a three pin plug?
Pratikroy
The plug itself will have a infinity value of resistance. If a load is connected to the plug, the internal resistance of the device will be present at the blades.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is the resistance value of gold?
22.14 n Ω·m at 20C
Which values of resistance is correct ac or dc?
AC current tends to flow towards the surface of a conductor due to what is known as the skin effect. This phenomenon acts to reduce the effective cross-sectional area of a conductor and, therefore, elevate its resistance. This elevated value of resistance is known as AC resistance.The skin effect increases with frequency. At 50/60 Hz, the skin effect is quite moderate and, so, the AC resistance is not significantly higher than the true (or DC) resistance of the conductor.As to 'which value of resistance is correct?' Well, the natural resistance of a conductor is directly-proportional to its cross-sectional area and resistivity, and inversely-proportional to its length and the type of current plays no part in this. This is the value that a DC current would 'see', so you could say that this would be the 'correct' value of resistance.
What is the resistance value for LED bulb in 12v DC circut?
48 ohms
What is the advantage of four probe method over other conventional methods?
I assume you are referring to methods of measuring small value resistances, as in locating short circuits on a PC card. Two probe is the method used by standard ohm meters. This works OK for most resistance values, as the resistance of the leads & probes is much lower than the resistance being measured. But when the resistance being measured gets very tiny (e.g. a few milliohms) it fails as the resistance of the leads & probe are of the same order of magnitude and are in series with it. Four probe solves this problem by using two probes connected to a current source to drive the resistance and a separate two probes connected to a precision voltmeter calibrated in milliohms. The voltage drop in the leads due to the test current does not get measured by the calibrated voltmeter, as it does in two probe method. There is no voltage drop in the measurement leads as the voltmeter is high impedance.
How do you convert galvanometer to an ohmmeter?
"An ohmmeter is an electrical instrument that measures electrical resistance, the opposition to an electric current."The unit of measurement for resistance is ohms (Ω).It is useful device for rapid measurement of resistance. It is consist of galvanometer and adjustable resistance Rs of known value and a cell connected in series. The resistance R to be measured is connected between the terminals.The series resistance Rs is so adjusted that when the terminals are short circuited i.e., when R = 0, the galvanometer gives full scale deflection. So the extreme graduation of the usual scale the galvanometer is marked 0 for resistance measurement. When terminals are not joined no current passes through the galvanometer and its deflection will be zero . Thus zero of the scale marked as infinity. . When R is not infinite , the galvanometer deflects to some intermediate point depending on the value of R scale can be calibrated to read the resistance directly.
The relationship between resistance and conductors is?
ALL resistance are conductors. just the magnitude value changes
What should a bad motor read in ohms if it is bad?
If an Alternating Current (a/c) motor is bad. The resistance will read very hi as in an open winding. ie: meg ohms Or very low as in a shorted winding. ie: 0.01 ohms It must not read any resistance to the housing or shaft. The resistance between leads should be a reasonable value and can be determined with : electromotive force divided by inductance equals resistance. example: 215 volt alternating current with name plate full load amperes of 10 should read very near 21.5 ohms resistance between leads.
What is inter base resistance in UJT?
The bulk resistance between the two bases, which will be different for different types of UJT. Consult the datasheet for the value.
What is the value for resistance 1100 ohms?
The number of ohms is, precisely, the value of the resistance.
Does measured value of resistance match the calculate value of resistance?
what is the diference betwean calculated and maesured value
What value of tester is to be used for measuring insulation resistance of three phase 600V cables?
The typical test equipment for this is a megger. The megger is connected to two conductors at a time to test the insulation between the two.
What is the difference between resistance and the resistivity?
Resistance is the value of a given wire in ohm but resistivity is value of the material with which that wire is made in ohm meter. R = rho * L / A Here rho is resistivity and R is resistance. L is the length of the wire and A is area of cross section
When only three colour are stripes present on the body of a resistance what is the replaced value of its tolerance?
If there is no fourth band (the tolerance band) then the component's tolerance value is 20%.
What is the difference between proximate and ultimate analysis?
practically there is no difference ..bt theoretically it has ...... ultimate analysis leads to the total summation while the proximate leads to the avg value .....
How do you test pickup coil on a ATV?
A pickup coil for an ATV may be tested by measuring the resistance across the coil's electrical leads and comparing this value against the expected range specified in the ATV's shop manual.# Disconnect the pickup coil assembly from the ignition system (e.g. the CDI unit or engine control module) # Identify the coil's electrical contacts on the connector # Measure the electrical resistance between the coil's contacts with an Ohmmeter or digital volt meter.Take care not to grab both leads of your ohmmeter with your fingers while measuring this value or you'll measure your body's resistance in parallel with the coil. It's not dangerous but it might corrupt your reading.The value for working part will vary by manufacturer and model, but will typically be between 100 ohms and 350 ohms.If the coil reads as an "open circuit", or the resistance in the high 10's of k-ohms or higher, your coil is damaged and likely non-functional.
What should be the resistance value of healthy earth pit?
what is the resistance value of a healthy earth pit
How designing stabilizing resistor in restricted earth fault relay?
To determine the value of Stabilizing resistor Rs = Vs/Is = If(Rct +2Rl)/Is Where, Rs = resistance value of the stabilizing resistor Vs = voltage at which the relay will operate Is = current flowing through the stabilizing resitor and the relay If = maximum secondary fault current magnitude Rct = internal resistance of the current transformer Rl = resistance of attached wire leads
