0
You need to know the Primary and secondary voltages to do the calculation.
we only have 100Kva Transformers on our salt furnaces as an example:
100000va / 12v = 8333 amps the secondaries , wire, and electrodes are water cooled.
Wiki User
∙ 13y ago
Wiki User
∙ 10y agoA 250 kVA transformer can supply a maximum of 250 kW but only to a load with a power factor of 1. For other loads the maximum power available is 250 kW multplied by the power factor.
Add your answer:
Earn +20 pts
Why transformer rating is not given in kw?
Transformer rating is based on the maximum temperature a transformer can run at. This temperature is dictated by the amount of current flowing through the transformer windings. This is why transformers are rated in KVA (voltage * current), not kW - it doesn't matter what the phase relationship is between voltage and current, just the magnitude of the current.
Why the transformer rating in kva why not in kw?
A transformer has separate ratings for maximum voltage and maximum current. Both limits must be observed. The maximum voltage is set by the magnetic flux density in the core, while the current limit is set by the size of the wire used in the primary and secondary windings. Multiplying the two together gives the VA or kVA rating.
How do you reduce Transformer 6VA to 3VA?
In 2 words, you cannot! It is like asking how can I make a 60W light bulb into a 30W light bulb. If you are wanting to know this because a specification dictates that you need a 3VA transformer then anything larger is OK. However, you must pay attention to the voltages on the transformer. Firstly, assuming that this transformer is to operate on the mains supply, it should have the correct primary voltage for the mains supply in your area. In most, though not all of Europe, it is standardised at 230V 50Hz. The secondary (usually the output) should have the desired voltage output. This, for example, might be 6V A.C. If it is the only output then, if it is a 6VA transformer, it will be able to supply 1A maximum current. If it is a 3VA transformer, supplying 6V, it will be able to supply a current of 0.5A maximum. The term VA is for Volt-Amps. It refers to the power that would be developed in a resistive load. Hence the secondary voltage (V) multiplied by the maximum current rating (A) gives VA. Thus, if you have a transformer rated at 12VA and the secondary voltage is 5V then the maximum current the transformer can supply is VA/V=12/5=2.40AAnother AnswerThe volt ampere rating of a transformer simply indicates the maximum load it can supply without overheating. The same transformer can supply ANY load below that value. So there's absolutely no problem operating a 6 V.A transformer at 3 V.A.
How is current controlled in welding transformer?
in welding machine, the transformer used is basically a current transforrmer. so by changing the tap of secondary side of transformer, we can increase or decrease the current in the transformer.
What is principle of Current transformer?
why does have to short-circuit secondary wire of current transformer ?
How do you calculate maximum earth fault current?
transformer max earth fault current
What is a full load current in single phase transformer?
It is the rated maximum current that can be taken from the transformer. This is equal to the VA rating divided by the output voltage. So a 6 kVA 240 v transformer would have a maximum current rating of 6000/240 or 25 amps.
Calculate the motor start current the source is 480v.feeder switch fuse is 2000.the transformer is 2500kva the motor is 400hp rpm1490 A457 V460 sf1.15 total amp base on other equip on trans is 485.8?
????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ?????????????????????????? ??????????????? ???????? GOOD QUESTION.....
How many amps does a 600 watt low voltage transformer box pull?
The transformer itself does not pull current. Whatever you connect to the transformer pulls current. Whatever the output voltage of the transformer is, divide that into 600 and you get maximum current possible without burning up the transformer. At 24V that's 25 amps.
Why transformer rating is not given in kw?
Transformer rating is based on the maximum temperature a transformer can run at. This temperature is dictated by the amount of current flowing through the transformer windings. This is why transformers are rated in KVA (voltage * current), not kW - it doesn't matter what the phase relationship is between voltage and current, just the magnitude of the current.
Will a 4.74 amp transformer fry a computer designed for a 3.42 amp transformer?
No because the current rating of the transformer is a maximum allowable current. If the computer still takes 3.42 amps it will be OK provided the new transformer supplies the correct voltage.
If a centre tap transformer rated as 12V-0-12V 1Athen what will be the secondary current of that perticular transformer?
The output voltage of a transformer is not connected to the maximum rated current. You state that the transformer is rated at 12-0-12 at a current of 1A, therefore the maximum (rated) current on the secondary would be 1A. Normally, transformers are rated in VA (volt amps) which is simply voltage x current, the voltage across the two 12v terminals would be 12+12 volts, making the rating of the transformer 24VA.
Why the transformer rating in kva why not in kw?
A transformer has separate ratings for maximum voltage and maximum current. Both limits must be observed. The maximum voltage is set by the magnetic flux density in the core, while the current limit is set by the size of the wire used in the primary and secondary windings. Multiplying the two together gives the VA or kVA rating.
What is the maximum transformer rating for distribution transformer?
100MVA
When is the efficiency maximum in a transformer?
the efficiency is maximum in a transformer when no load loss is equal to load loss.
What is current choking in transformers?
The "current choking" means that the maximum capacity of a transformer is not being utilized. To prevent it from ever reaching its maximum capacity a lower value of over current protection or fuse is installed. The purpose is to use larger capacity transformer available but using smaller distribution and cables just sufficient for the application to lower the installation cost.
How do you reduce Transformer 6VA to 3VA?
In 2 words, you cannot! It is like asking how can I make a 60W light bulb into a 30W light bulb. If you are wanting to know this because a specification dictates that you need a 3VA transformer then anything larger is OK. However, you must pay attention to the voltages on the transformer. Firstly, assuming that this transformer is to operate on the mains supply, it should have the correct primary voltage for the mains supply in your area. In most, though not all of Europe, it is standardised at 230V 50Hz. The secondary (usually the output) should have the desired voltage output. This, for example, might be 6V A.C. If it is the only output then, if it is a 6VA transformer, it will be able to supply 1A maximum current. If it is a 3VA transformer, supplying 6V, it will be able to supply a current of 0.5A maximum. The term VA is for Volt-Amps. It refers to the power that would be developed in a resistive load. Hence the secondary voltage (V) multiplied by the maximum current rating (A) gives VA. Thus, if you have a transformer rated at 12VA and the secondary voltage is 5V then the maximum current the transformer can supply is VA/V=12/5=2.40AAnother AnswerThe volt ampere rating of a transformer simply indicates the maximum load it can supply without overheating. The same transformer can supply ANY load below that value. So there's absolutely no problem operating a 6 V.A transformer at 3 V.A.
