Brake Fluid and Lubrication
Ford Contour

What kind of brake fluid do you use for your 2000 Ford Contour?

323334

Top Answer
User Avatar
Wiki User
2005-09-26 00:39:10
2005-09-26 00:39:10

Probably DOT 3, Although DOT 4 supercedes DOT3. Check your owner's manual.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

According to the 1997 Ford Contour Owner Guide : The BRAKE FLUID reservoir is ALSO the CLUTCH FLUID reservoir

User Avatar

DOT 3 that meets Ford specs ESA - M6C25-A

User Avatar

According to the 2000 Ford Expedition Owner Guide : ( DOT 3 brake fluid ) meeting Ford specification ( ESA-M6C25-A )

User Avatar

In a 2000 Ford Windstar : ( DOT 3 brake fluid meeting Ford specification ESA-M6C25-A ) according to the Owner Guide

User Avatar

how change brake fluid . i have ford focus lx 2000.ans how change air filter.

User Avatar

DOT ( 3 ) brake fluid meeting Ford specification ( ESA-M6C25-A )

User Avatar

You have to step on the brake pedal and hold it, then shift into gear.

User Avatar

According to the 2000 Ford Explorer Owner Guide : DOT 3 brake fluid ( meeting Ford specification ESA-M6C25-A ) is used

User Avatar

In North America ( DOT 3 brake fluid ) meeting Ford specification ( ESA-M6C25-A )

User Avatar

According to the 2000 Ford Contour Owner Guide : For the manual transaxle ( transmission ) ( 2.0 U.S. quarts of Motorcraft MERCON automatic transmission fluid )

User Avatar

The automatic transaxle fluid dipstick is near the brake fluid reservoir ( going towards the passenger side )

User Avatar

look at the level in the master cylinder near the firewall.

User Avatar

it is located where the transmission is and is very easy to change. on a 2000 ford contour that is.

User Avatar

you put it in the same place your trans dipstick is, by the brake fluid container below it, it gas a yellow handle

User Avatar

I was looking at the 2000 Ford F-350 Owner Guide and the drawing shows that when you look in the engine compartment from the front of the vehicle , the clutch fluid reservoir is by the firewall just to the left of the brake fluid reservoir ( like the brake fluid reservoir it takes DOT 3 brake fluid meeting Ford specification ESA-M6C25-A )

User Avatar

Remove the Master Cylinder Reservoir cap and fill with fresh brake fluid from an unopened can to the full mark. Be sure and look on the cap and use the correct fluid. Normally DOT3.

User Avatar

According to the 2000 Ford Contour Owner Guide : The 5 speed manual transaxle ( transmission ) takes : ( 2.0 U.S. quarts of Motorcraft MERCON automatic transmission fluid )

User Avatar

The weight of a Ford Contour will vary depending on the year and model of the Contour. A 2000 Ford Contour has a curb weight of 3,126 pounds.

User Avatar

http://contour.org/mods/mods.php?s=howto&displayid=38

User Avatar

According to the 2000 Mercury Mountaineer Owner Guide : ( Yes , DOT 3 brake fluid , meeting Ford specification ESA-M6C25-A )

User Avatar

Your 2000 Ford Contour cannot reverse because of a transmission failure problem.

User Avatar

Department Of Transportation ( D.O.T. ) 3

User Avatar

On a 1998 Ford Contour : The BRAKE FLUID reservoir is also the CLUTCH FLUID reservoir It is located in the engine compartment , near the firewall ( that's the metal wall that divides the passenger compartment from the engine compartment ) It is located on the drivers side of the vehicle

User Avatar

To put brake fluid in a 1997 Ford Explorer, you must locate the brake fluid reservoir. Once you locate it, unscrew the cap, and replenish the brake fluid.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.