Want this question answered?
When Ever they are worn out. If they are pounded with dents in them that it might be time for a change.
It depends, when the light reflects on the foil paper it might give out the shape of the little dents on it.
Some retailers buy scratch and dent aplliances, they get dented during shipping and delivery and are sold cheeper..
'Dents', which is pronouned 'doh (soft o)-n-ts'. If you were just talking about one tooth, it would be 'dent', pronouned 'doh-n'. You might see/hear it in a sentence as 'Je brosse mes dents' which means 'I brush my teeth'
They found it out by dents, teeth and bones. They can tell by the dents because if anything hit them. This might cause it to be a battle or something what hit them. That can tell them what there living was like. There teeth can be found out as what they ate. How they found it out was by little bits of food stuck in there teeth and how the teeth looked. Last but not least there bones if they have a crack in there bone by something or some who attacked them or they might of just hit it. This will give u a clue of what there days were like.
hardwood is more durable than pine, it resists dents and breakage but is usually more expensive as well. You might also just like the look of the tighter grain and pattern of hardwood furniture.
There are a few reasons why your alternator might keep going bad such as rusty latches under the car. You may also have leaks, dents, or parts that need to be replaced on the vehicle that are effecting your alternator.
I had this problem when my civic was in a front end collision. I opened the hood and pounded out the dents with a rubber mallet, but then the hood wouldn't latch. The hood is curved and by pounding out the dents in the front, i had bent the front of the hood upwards, making it impossible for the latch to fully engage. I solved the problem with a few well placed mallet blows near the middle of the hood, which brought the front end of the hood back into its more natural position. This might not be the optimal solution if you hood isn't already banged up, but it might set you in the right direction. I had this problem when my civic was in a front end collision. I opened the hood and pounded out the dents with a rubber mallet, but then the hood wouldn't latch. The hood is curved and by pounding out the dents in the front, i had bent the front of the hood upwards, making it impossible for the latch to fully engage. I solved the problem with a few well placed mallet blows near the middle of the hood, which brought the front end of the hood back into its more natural position. This might not be the optimal solution if you hood isn't already banged up, but it might set you in the right direction.
Every person has dips, dents, and "knots" on the skull. These are inconsequential. They have no negative consequences. However, from time to time, a place might be sore, especially when touched. Doctors will simply tell you, "Well, then don't touch there!"
This ancient giant is the tallest living being on earth that we know of. If your prospect is very tall, has dense, reddish bark, and needles instead of broad leaves, it might just be a redwood. For a much more detailed explanation, please see the related link below:
Casters are a product that was designed to be put on the bottom of table legs, chair legs or other items that might be placed on the floor or carpet. These are meant to protect the flooring from scratches or dents when the furniture is being used. Some casters have small wheels attached which also allow one to move furniture easily.
Use the same techniques you would use to smooth dents in bodywork but use a heavier dolly or spoon and a bigger hammer. After you get the dents out, you finish it with a body grinder and keep taking it down with progressively finer grit sandpaper. Since it will need to be re-chromed after this, you might as well take it to a chrome shop and pay them to do the work because they are going to re-do the work you did because that's the way they roll. If you are going to paint the bumper, you can use Bondo or other body filler like you would on any of the rest of your sheetmetal. See Link to get in touch with people who can provide tips on painting bumpers.