0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What model cars have the dohc g200 Isuzu engine?
Hasta donde conozco el motor Isuzu G200, solo posee un arbol de leva en la culata, por lo menos en mi pais no hay motores g200 con doble arbol de leva en la culata. La bibliografia tampoco los señala!!!
What is the head stud tension for a 1985 g200 Isuzu?
Head stud tension on Isuzu G200 Phase 1. 29ft/lbs or 39 newton meter Phase 2. 54ft/lbs or 73 newton meter Phase 3. 72ft/lbs or 98 newton meter
Does the 1985 holden rodeo have hydraulic lifters?
iF IT IS A PETROL 2.0L G200 ENGINE THEN NO
What is Max flight time of gulfstream g200?
7H
How do you remove a JVC KD-G200?
How do you remove a stuck CD it plays but does not eject
How many gallons of fuel does a gulfstream G200?
15, 010 lbs which comes to 2240 gallons of fuel.
How much is 200 mg in pounds?
Well, an mcg is an abbreviation for microgram used in medical labeling and contexts. A microgram is 1/1000 of a milligram, and is one of the smallest units of weight/mass commonly used. Therefore, 200 mcg (200 micrograms) is 0.2 mg.
Jvc kd-g200 CD does not eject?
I found the answer, so I will share for others:For a JVC KD-G200 car stereo / CDSee if "No Eject" is set. Press the CD button and the CD Eject button at the same time for more than 2 seconds. "NO EJECT" or "EJECT" will flash, obviously you want eject. (JVC pg 16)This did not work for me; I had to reset the system. Press and hold for more than 2 seconds the select and power button. The system powered down and the CD came out. Of course, all of the radio presets went away. (JVC pg 2)http://resources.jvc.com/Resources/00/00/95/GET0182-001A.pdf
What is the retail price of a Gulfstream G200?
a G550 is 51 million Based on more recent information: A new G200 is currently going for $21.5 million. However, the first available delivery date from Gulfstream for a new acft is 3q of 2009. A new G550 has a retail price tag of $47-$48 million, with the higher price being for a G550 equipped with BBML & DirecTV. First available delivery date for the G550 is 3Q of 2012. If you want your G550 any earlier, expect to pay a premium of $10 to $12 million or more. Current asking price (from individuals) for a position on a G550 and a delivery date within the next 12 months is in the $57 to $65 million range. The just announced G650 has a price tag of $58 million and a delivery date of mid 2012.
2000 mg equals how many grams?
The metric prefix milli indicates that there are 1/1000th of a unit present. If there are two thousand 1/1000ths, that means there are 2 base units, or in this case, 2 grams.
Hi beams dont work on 95 geo tracker every thing else works replaced turn signal switch a few years back already?
AnswerCheck the bulbs - maybe burned outCheck to see if there is a fuse in the poweer distribution boxbetter answer:is car DLR , day light running ?if yes , HL can fail for many reason, including brake alarms !if not DRL.then 2 bad HL, ( no i dont believe it) sorry?the HL switch grounds the HIGH beams.so pull the connector on column shaft the feeds the combo switch and put a ground wire on the colored pin that is RED.Red white is lows.RED is HIGHS.your answer in 1 minute test.if this fails the combo is bad or the ground to it is bad G200
What is the problem with a Geo Storm when it tries to stall when idling at a red light andor when the same car wants to stall when you try to back it up in the parking lot?
Isuzu engines commonly exhibit erratic idle problems The engine revving and dropping in rpms, sometimes dropping almost to the point of dying. There are several things that can cause this problem:Leaks in the vacuum hoses or aged, cracked hoses can let in air that is not being metered by the ECU's sensors.Leaking or sticking EGR Bypass valve may be allowing exhaust gasses into the intake when the engine is not under load (idling). Loose electrical connections in the engine sensors can cause problems.On G200, 4ZC1, and 4ZD1 Engines: The Idle Control Valve / Idle Solenoid may not be functioning properly.On 4XC1, 4XE1, and 4XF1 Engines: These engines are notorious for idle speed revving and dropping. Thus far, no single simple answer has been successful in all situations has been offered.Before you do anything at all, check the ignition timing and reset it to factory specifications (9-11 degrees). Incorrectly adjusted ignition timing (too far advanced timing), will cause havoc within the ECU and the engine will not idle correctly.After this, the first step would be to carefully remove the IAC control valve and clean it with carburetor cleaner, xylene, or some other solvent and a tooth brush.Also clean the passages in the throttle body, and then reinstall the IAC valve, making sure to reinstall the O ring also. This may resolve the problem in some very mild cases.Check the throttle cable adjustment. If the throttle cable is adjusted too tight, the throttle position sensor will not read that the throttle is closed at idle, and this will cause the computer to fight to lower the idle speed. Make sure there is some slack in the line and that the throttle arm easily and consistently rests against the throttle adjustment screw whenever there is no pressure on the pedal. If it does not, then examine, repair, or replace the throttle cable and gas pedal if anything is found in either of these assemblies to show the cable or pedal is sticking. If this does not help, things get much more complicated. These engines are set up with a learning mode and the computer controls all functions, including idle speed, based on the signals from the sensors. If one sensor begins to malfunction but does not go totally dead, the computer will continually try to adjust, causing all sorts of symptoms, and even running the trouble codes will not help, because it will show nothing unless the sensor is dead.The best and easiest solution is to have a service department use a scan tool to determine the problem. Anything else would be a futile effort to guess and get lucky on what the problem is and pray that you don't waste hundreds of dollars replacing sensors that are not defective.The throttle position sensor on these vehicles can not be adjusted. This does not mean that the sensor can not be twisted on its mounting bolts so that the baseline voltage reading is different, it means that the baseline voltage reading is meaningless, and the computer takes whatever the lowest voltage reading sensed to be 0%, no matter what that voltage may be. Using the scan tool and observing the physical position of the throttle linkage at the throttle body, observe that the percentage reading does not always return to 0 though the linkage has physically returned to its fully closed position. This appears to be a voltage variance in the sensor signal from the ECU. The voltage sent to the sensor from the ECU increases above idle speed above the 5 volts specified, and though the linkage and sensor return to the fully closed position, the increased voltage in the sensor signal causes an increas3 in the voltage returned by the sensor, so the ECU does not believe the throttle plate is fully closed, and tries to continually adjust the ignition timing and fuel injectors to for a condition it can't determine is idle or above idle. If you insist upon this hunt-and pray method, your possibilities are: coolant temperature sensor, mass air pressure sensor, intake air temperature sensor (thermistor), oxygen sensor (exhaust), etc. You should disconnect the battery for several minutes after making any changes to clear the learning portion of the computer memory, this way, if you are lucky enough to guess which sensor is bad and replace it, the computer will not continue to try to compensate for the bad sensor that it sensed before.If you decide to take the vehicle to a service department to have it scanned, make sure that they have and can operate a Delco Tech I tool and have the software to service your vehicle. Know that these Delco computers (ECU or CPU as they may call it) are flash programmed. They do not have a static programmed prom chip, and rather are "flash programmed" by loading with the software from the Tech I while the computer is installed in the car. They do have learning modes, do have a memory, and are programmable. You will find that many dealer service departments have little or no experience working on anything other than trucks and sport utility vehicles. They may have no experience in dealing with the Delco based computer controls on these vehicles, and may even make claims that these computers are not programmable, etc. Make sure that you quiz the people who you intend to have service your vehicle. If they are not familiar with the Delco based computers, claim anything other than that they are fully programmable and flash programmed using a Tech I, or indicate that they lack the hardware and software to service your vehicle, do yourself a favor and take your vehicle somewhere else to someone who has at least the slightest idea of what they are doing.Also note, that there have been numerous recalls on the Delco ECUs used in the Isuzu and Storm models which are listed at the website. Specifically, all 1991 Isuzu cars have a standing recall # 9101001 under General Recalls for a ECM replacement campaign, and all 1990-91 Geo Storms have a standing recall # 91C066E under Emissions Recalls for ECM replacement because of emissions non-compliance. It appears that the computers should be recalled, and that a recall was issued by Isuzu, but that this recall is no longer being honored by the company. If this is the case with your vehicle, changing all the sensors will have no effect, and only by replacing the ECU will you ever solve the problem. Lastly, to improve drivability without fixing the problem so that you can use the car despite its idle problem, if you find that the vehicle is revving and dropping and trying to die, you may wish to try one of the following temporary cures:If you live in a climate with little temperature variation and it is always 70 degrees Fahrenheit or above, you may wish to start the engine, allow it to warm up, wait for the engine to idle at a normal speed, and then simply un plug the IAC solenoid. This disables the IAC solenoid and the computer will not be able to continually try to correct for whatever problem it has that is serious enough to warrant correction, but not serious enough to bring up a trouble code when the codes are run. Disconnecting the IAC solenoid will, however, make it almost impossible to use the air conditioning, as the IAC solenoid usually adjusts the idle speed up to compensate for the increased drag of the compressor. Disabling the IAC solenoid eliminates this, and the engine will die if you turn on the air conditioning. This will also happen if the temperature drops enough, and engine warm up will become difficult. Adjusting the throttle plate stop on the throttle body is the second possible action, which works much better if you are in a climate where the temperature is not steady and cooler whether is normal. Note that the throttle stop is set at the factory, there are no instructions to return the throttle stop to its original position, and if you have the vehicle serviced by a dealership service department, their instructions are to replace your throttle body ($400.00 or more) if the adjustment screw has been tampered with. That said, you can adjust the idle screw in several threads to artificially raise the minimum idle speed. The computer will still try to compensate, but will not be allowed to let the engine speed drop low enough to kill the engine. The side effect will be that once the engine gets hot, the idle speed will hover between 2,000 and 3,000 RPM often when you pull to a stop at a stop light or stop sign. Sometimes it will work its way down after several minutes, and sometimes it will simply hover at that point. It is annoying, but much less so than having to continually restart the engine every time you come to a stop. This temporary solution should not be used in the long term. It is not good for the engine to run above idle for long periods with no load. In addition, it is not good for the life of the clutch to start from a standing stop at 2,000-3,000 RPM all the time.
