0
What occurs when two adjacent conductors make electrical contact and bypass a portion of the circuit?
Wiki User
∙ 6y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
The main reason why you should avoid bodily contact with ground while working on live electrical equipment is that such contact will?
The main reason why you should avoid bodily contact with ground while working on live electrical equipment is that such contact will complete a circuit. If you are in contact with any electricity, this means that your body becomes part of the path for the electricity and it will pass through you as it heads into the ground.
What is A mini circuit breaker that responds to shorts or contact with water?
GFI is a mini circuit breaker that responds to shorts or contact with water
Why would a circuit breaker switch spark?
the circuit breaker spark when it comes an over load, loss contact,but the probable cause is loss contact...and also the circuit breaker is going to be damage or destroyed.
Is a lamp contact a conductor or insulator?
The "contact" ... that is, the point where one side of the power circuit is connected ... must be a conductor. When the switch is 'open', then one contact is physically separated from the other one, and no current flows between them. But the contacts themselves are still conductors.
What is an electrical fault?
Some people will define the cause of an electrical fault as a "short circuit" but that is too simple an explanation because it doesn't explain how it is caused. An electrical fault is the name given to any situation where some electrical current goes where it was not intended to go. This situation can be caused by damage to the protective insulation around a wire - or around some other part - which puts the wire or part in contact with a different wire or part that it was not designed to touch because a difference in voltage has to exist between them to allow an item of electrical equipment to do its work. If an item of electrical equipment gets dropped accidentally - or if something else hits it violently - that action can easily damage the insulation material or close an air gap that was designed to keep two parts electrically separate within that item of equipment. Another way an electrical fault can be caused is by physical deterioration of some insulation. Such deterioration can be caused by many factors such as, for example, the temperature of the equipment being too high or if some unprotected equipment is exposed to wet or damp conditions. Such factors can put stresses on the insulation which it was not designed to withstand and it breaks down and causes an electrical fault to occur. If an item of electrical equipment (or an electrical wiring circuit which connects different pieces of equipment together) is properly designed, then, if an electrical fault occurs, protective circuit breakers should trip and/or fuses should blow to stop the flow of any excessive current that is the result of the electrical fault, thus helping to prevent any fires and/or explosions from happening because the fault occurred.
What occurs when two adjacent conductors make electrical contact and by pass a portion of the circuit?
That is called a short circuit.
When a tree falls on power lines grid what fault is it?
It depends on what happens. It could cause adjacent conductors to clash (line-to-line short-circuit fault), or it could break a conductor which then makes contact with the ground (line-to-earth short-circuit fault), or it could be neither of these.
Is there any short circuit between strands in stranded conductors?
As the strands are in contact with each other, of course there is.
Effects of connecting poor contact in electrical circuits?
An effect of connecting a poor contact in an electrical circuit could be intermittent current flow.
How do you say no contact in latin?
No touching, as in "no contact" between elements of an electrical circuit: nulla contagioNo communication, as in "no contact" between acquaintances: nulla communicatio
What causes contact chatter in electrical circuit?
Overload can cause contact chatter. Once the contact closes, the voltage in the circuit collapses and that causes the relay to drop out. At this pint the relay energizes, since the voltage is back. This cycle will continue on.
Does the spring in a flashlight complete the circuit or does it convert electrical energy into light energy?
A flashlight's spring is just to ensure a good electrical contact at both ends of the battery.
What are the definition of electrodes?
An electrode is an electrical conductor used to make contact with a nonmetallic part of a circuit (e.g. a semiconductor, an electrolyte or a vacuum).
The main reason why you should avoid bodily contact with ground while working on live electrical equipment is that such contact will?
The main reason why you should avoid bodily contact with ground while working on live electrical equipment is that such contact will complete a circuit. If you are in contact with any electricity, this means that your body becomes part of the path for the electricity and it will pass through you as it heads into the ground.
Why did my Wipers stop working on 93 Chevy silverado?
The electrical contacts on the pulse board are likely not making contact or are damaged in some way. You can replace the pulse board (about $25 from pep boys.), it is located on the firewall, next to the wiper motor. Actually looks like a square box adjacent to the wiper motor. You may just need to clean the electical contacts inside. They are two brass or copper pieces which make contact with a spiral wire on the circuit board. Make sure they are clean amd making contact with the circuit board.
What is a path through which current flows?
A path through which current flows is generally called a circuit. Some might say a complete circuit to denote a "closed loop" through which electricity can leave one electrode or contact on a voltage source, travel through some conductors of some kind, and then return to the other electrode or contact on the source.
What are arcing contacts?
Whenever an electrical contact is made or broken, an electrical spark jumps through the air between the two contact points while they are very close together but not yet, or not any longer, touching. That spark jumping is an electrical arc and the event is arcing contact. The main cause of arcing is the property of a circuit to maintain the continuity of the current, so whenever the contacts separate to break the circuit the air (or any dielectric medium that is used) ionises and continuity of the current is maintained, at least momentarily.
