0
What part of the U.S. had the most welding and soldering establishments?
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Is welding bad and how bad.what can welding cause?
burns and cancer for the most part
What is cold-soldering?
cold soldering is when the soldring part is not well soldard or the soldring has being disjoint.
Is mig welding better than gas welding in terms of strength?
It depends on what metal you are welding and how thick it is, but in general, no. Any process that will raise enough heat for adequate weld penetration is for the most part equal.
Why would you use a soldering stand?
why do you think its best for soldering iron to have soldering stand
What is the outer coating on a welding rod?
The flux is the outer coating on a welding rod. The flux is a very important part of the welding rod.
Why do you think is it best for a soldering iron to have its soldering stand?
I ended up in need of a welding iron stand and didn't like the looks of any I could discover. While I don't do a gigantic measure of welding however this will be perched on work areas or work stations where I'll see it a great part of the time. Along these lines, I required something that would be essential and practical and additionally tastefully engaging. I chose to do one with a marble base and one with terracotta. They were made in the same way. This is basically a regulated of the terracotta model with a couple of shots of the marble.
Why do you think is it best for a soldering iron to have is soldering stand?
I ended up in need of a welding iron stand and didn't like the looks of any I could discover. While I don't do a gigantic measure of welding however this will be perched on work areas or work stations where I'll see it a great part of the time. Along these lines, I required something that would be essential and practical and additionally tastefully engaging. I chose to do one with a marble base and one with terracotta. They were made in the same way. This is basically a regulated of the terracotta model with a couple of shots of the marble.
Why do you think is it best for a soldering iron to have it soldering stand?
I ended up in need of a welding iron stand and didn't like the looks of any I could discover. While I don't do a gigantic measure of welding however this will be perched on work areas or work stations where I'll see it a great part of the time. Along these lines, I required something that would be essential and practical and additionally tastefully engaging. I chose to do one with a marble base and one with terracotta. They were made in the same way. This is basically a regulated of the terracotta model with a couple of shots of the marble.
Why do you think it is best for a soldering iron to have it soldering stand?
I ended up in need of a welding iron stand and didn't like the looks of any I could discover. While I don't do a gigantic measure of welding however this will be perched on work areas or work stations where I'll see it a great part of the time. Along these lines, I required something that would be essential and practical and additionally tastefully engaging. I chose to do one with a marble base and one with terracotta. They were made in the same way. This is basically a regulated of the terracotta model with a couple of shots of the marble.
What is difference between welding and weld-ability?
ANSWER:Soldering is a joint repair for two pieces of metal, like a chip to a circuit board using lead. Welding is taking two pieces of metal and heating them up to the same temperature and making a single piece of metal out of two separate pieces. I was taught that soldering,as it relates to piping, is the heating of the base metal to a point to where the filler metal will melt and fill the gap between the two pieces of metal being soldered. The base metal is NOT melted, only the filler metal. Soldering is usually used to join non-ferrous metals. Welding is when the base metal is heated to a point where it will melt and , with the filler metal, becomes part of the weldment. In other words, the two pieces become one, and the resulting weld is now a blend of base metal and filler metal.soldering is a very low heat (melting temperature of the soldering alloy is less than 840 degrees Fahrenheit), semi-adhesion process, final product: 2 base materials, and a filler material on top. welding is high heat fusion process, final product: a solid blended material
Is there a replacement iron for Part No 64-2185 Digital Soldering Station?
yes
How many establishments did NAICS Code 333518 cover in 1998?
According to the U.S. Census Bureau's Statistics of U.S. Businesses, 448 establishments operated in this category for part or all of 1998
