0
What points on the back of the instrument cluster do you need to solder on my 95 neon?
Wiki User
∙ 15y ago
Solder all the pins connected to the two large plugs, there is about 20 or so connection, just solder them all on the back of board.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Why does my 97 Plymouth voyager while driving my instrument panel quits working and van chugs?
still havent figured out the chugging but the instrument panel issue can be fixed by reheating all of the solder points on the back of the cluster again.
Sending unit is not working no fuel 1992 Volvo 940 gle?
This is a common problem with the instrument cluster connections on the back of the cluster itself. The contacts need to be resoldered. Remove the cluster, and use a solder iron to heat and reflow the solder connections.
97 Dodge Intrepid dash goes out when I hit a bump and comes back on when I hit another bump. It is analog please help?
Remove the instrument cluster and tear it down, re solder and points on the rear 20 contact points that appear flawed.
How do you get to or where are the instrument lights on your 89 Toyota 4x4 pickup?
Remove the dash and remove the instrument cluster, the lights are in the back of the cluster.
1996 DODGE NEON no lights on dash at night?
First check the dimmer by turning the headlight switch knob. If that doesn't work, next you may need to replace the fuse or the bulbs that light the instruments. You will need to remove the instrument cluster to access the bulbs. If that doesn't work your instrument cluster may need to be replaced. Neons have a common problem with weak solder points on the circuit board for the instrument cluster. To access the instrument cluster, pop off the top of the whole dash with a trim stick or plastic putty knife. It is also possible for a wire in the harness behind the dash to be broken or cut, but this is unlikely unless someone has been working back there.
Why would 1993 Chevy astro van instrument panel lights not work whenthe fuse is good?
check the instrument cluster connection in back .. i got one and they would work sometimes then shut off .. i hit the dash cluster and they came on .. hense a bad connection at back plug on instrument cluster .. it runs through the plug at back of instrument cluster. sometimes the connection gets dirty doesnt make good contact. clean them up . fix is to take the instrument cluster out and clean up the connections in back.
How do you change a Chevy S-10 instrument panel light?
remove the trim panel around the instrument cluster then remove cluster. On the back of instrument cluster are the bulbs just turn them half a turn and they come right out.
Instrument cluster for a 1998 Dodge Neon no power on speedometer odometer oil fuel.?
buy a new instrument cluster or check the wires in back my car had that problem and it was a loose connection to the back of the panel
How to disable annoying key reminder chime noise telling you key is in ignition and driver's side door is open in a 1997 Subaru Legacy Outback?
The chime is located in the instrument panel on these model Legacys. Remove the cluster outer ring 4 screws. Then remove the instrument cluster by removing another 4 screws and the 5 wire connectors on the back side. On the back side of the cluster is the circuit board and indicator lamps. On the left side, next to the fuel gauge, is two solder points marked BZ+ and BZ-. These are the connections to the chime. Take a screw driver or exacto knife and scratch out the connection to BZ+. The chime is now deactivated. Before you put the cluster back in, take this time to replace any indicator bulbs not working. Reconnect the wiring and re-attach the instrument panel.
97 camaro rs the instrument light quit working you checked the fuse box what next?
Pull out your instrument cluster and check the back of the cluster for any blown bulbs.
How do you fix the odometer display it only works intermittently and the Tachometer seems to be connected to the same circuit in a Chrysler Sebring?
there is probably a broken solder joint on the instrument cluster circuit board. if you look at the circuit card itself there will be 2 resistors that look burned. by them there is a solder joint that connects the front and back of the board. check to see what side is not making connection and add solder to it. it takes a couple hours to do, and the solder job doesnt need to be perfect.
Your polo hatch back 2003 instrument cluster smook wont tart?
hy i got the same problem mow i need a instrument cluster dont know wher to get one
