0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you install piston rods onto pistons?
It depends on if the connecting rods use a full-floating or a semi-floating design. If it is a full-floating design, the piston should have spiral clips that snap into the side of the piston where the wrist pin slides trough to hold it in. Position the rod and piston, and slide the wrist pin through. Then install the clips. If your vehicle has the semi-floating design, the wrist pin is pressed into the connecting rod. This will require a shop press and the proper adapters to press the wrist pin into the connecting rod.
How do you rebuild a cr500 motor?
Two stroke engines are very easy to rebuild. The transmission component is not. The typical rebuild of a two stroke engine consists of removing the cylinder and replacing parts on the piston assembly. Before you order any parts, inspect the cylinder wall for wear and marking. If the cylinder is damaged you will need to get it machined and then order an oversized piston and ring to go with it. If its not damaged, order a standard (or performace) top end rebuild kit wich comes with a piston, piston ring, piston pin, piston pin bearing, and gaskets. So, for your standard rebuild of the top end you would remove one of the snap rings on either side of the piston pin. This will allow you to push the piston pin out from the opposite side. Once the pin is out the piston will come off the connecting rod. Take note of the piston orientation for assembly. The piston pin bearing will now be accessable (you will find on the connecting rod where the piston pin attached the piston). Minor assembly of the piston prior to installation makes it a bit easier to assemble. Place the piston ring on the piston and align the gap with the small pin you will see in the ring groove (turn the piston ring until it falls into place). Install 1 of the snap rings in the piston where the piston pin slides through it. The piston is now prepped for installation. Place the new piston pin bearing in the connecting rod with some assembly grease to hold it. Place the new piston onto the connecting rod so the hole in the piston matches the hole on the connecting rod. Slide the piston pin through the piston, connecting rod, and into the other side of the piston until it contacts the snap ring you installed earlier. Install the last snap ring into the piston to hold the pin in place, cover the outsides of the piston in assembly grease and lower the cylinder onto the piston. If you don't have a piston ring compressor you can hold the piston ring tight to the piston with your fingers. If you encounter any resistance when your putting on the cylinder you can LIGHTLY press the piston ring into the piston with a small slot-head screwdriver. Once that is together you should look up the torque specs for your make/model or if your not that picky just tighten them up at your discretion. If your looking to do anything on the bottom end of the motor or in the transmission I would HIGHLY recommend getting it done at a shop. Unless you know what you are doing you will have a puzzle of gears and springs to put back together.
Your 1987 Fleetwood has the 5.0 engine and it runs good and starts easily but it smokes like a son of a gun mainly blue smoke any ideas?
If smoke is coming from the tailpipe, then could be worn rings, burned piston or valve guides are gone. Compression test will check rings and burned piston. If from under the hood, check valve cover leaks onto the exhaust manifold.
How does one install MySQL in Mac OS X?
It is very easy to install MySQL directly onto the Mac OS X. MySQL can be downloaded onto the Mac OS X. When the download is complete, the folder should be opened and the executable should be launched. From there, just follow the prompts to install.
How do you install 3 piece oil rings in mgb pistons?
The set consists of two scraper rings, very thin, and thicker, usually "corrugated" spacer or expander. Install the spacer first onto the piston, taking care that the ends do not overlap, but will butt against each other. This is to assure that the expander does indeed keep the scrapers pressed against the cylinder wall after installation Then, starting about 1/3 around from the point where the ends of the spacer meet, install the bottom scraper by gently twisting the ring across its diameter so that one end is lower. Place this lower end into the ring grove below the spacer, then gently work the scraper down the side of the piston until it is fully in the grove below the spacer. Throughout the process, continue to make sure the ends of the spacer do not overlap (very easy to do, so be careful here) Install the top scraper in the same manner as the bottom scraper. Once done, and the compression rings (the two top rings) have been installed, lubricate generously with your favorite engine oil prior to installing in the cylinder Rick Morrison
Can you install flash onto a 3ds XL?
No, you can't install third-party software onto a 3DS.
Does the ISS have moons or rings?
No. It does not have enough gravity to "hold" onto rings, let alone a moon.
How do you install a cast iron flange on a cast iron pipe?
You can buy the new cast iron flanges, with the expandable O rings that push into the pipe or you'll have to do the old style or pouring lead onto a cast iron flange. The latter option should only be done by professionals.
What is the meaning of piston protrusion?
Piston Protrusion is the distance the piston sticks out above the surrounding cylinder. Protrusion means sticks out. A Domed Piston to create high compression ratios for race engines Will do this. A brake caliper piston protrudes to press the brake pads onto the rotor.
When you install a game onto your computer where is the information stored?
It should either be in programs or a icon on the main screen. Good luck!
Can you install java onto an iPad?
Java cannot be installed onto an iPad
If you install windows 7 on your laptop can you take the Windows Vista that was previously on your laptop and install it on your desktop computer?
This shouldn't be a problem normally, since you paid for a copy of that OS. The operating system should have drivers for the desktop, and it should install onto the desktop without any problems
