0
Special bolts! Do not replace with generic will fit bolts!
But the head size on my car is 18 MM
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is their a oversize bushing kit for 2003 S-10 door hinge. already have a bushing kit in it. holes on door hinge ova-led?
I remove the door, weld up the holes and redrill them to the correct size.
What size tires does a 2005 Dodge Neon use?
Well, your car's original tire size should be on the label that is located at the door frame. Just open your door and look where the hinge is. (not at the door but where the door meets the frame). I believe it should be P175-70-R14
Engine size for a 84 fiero?
150 ci
Where hinge joints are located?
The knee is a hinge joint. All the other joints have a certain amount of side movement. 2nd Answer: The elbows are also classified as hinge joints - other than size, they are almost identical to knee joints.
Will fiero 1984 windshield fit 86 fiero gt?
Yes it will fit. All Fiero windshields are the same size. They only vary in the amount of tinting or top shading.
How do you replace door hinge pins and bushings on 1994 Mercury Cougar?
open door ,prop door at the back end with floor jack, take two bolts out of door hing,take two remaining bolt from car side of hing then there is a bolt that is backwards you have to take the nut off of it .(it has a hole for a socket behind the kick panel right beside the e-brake pedel ) then you have to grind the( top) of the pin off and drive it out and old bushings --then you have to drill the car side of hing out to the right size of new bushings then put it back together [ make sure you drill the side that bolts to car not the door]
What is the size of the gas tank for a 85 v6 fiero?
9.7 gal
What size is the gas tank on l987 Pontiac Fiero SE?
10 gallons.
How to replace a 1993 Chevy blazer full size exterior door handle?
You will need to remove the inside door panel of your 1993 Chevrolet Blazer. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
How do you replace a car door hinge pin?
First you need to get the right tools for the job and the right parts to fix the problem. There is a hinge pin in both the upper and lower hinges and four brass bushings and there is two different size bushings in each hinge and also two hinge pin retaining washers. As for the tools, you need a spring compressor, jack, hammer, punch. First, open the door all the way and put jack under door. I like to use a 2-by-4 board on top of the jack to help spread the weight of the door out a little. Next, if the door has a wiring harness in the jamb loosen the rubber insulation form both the door and the body. This gives a couple of inches of slack in the wiring. Next use the spring compressor to remove the spring, then use the punch and hammer to drive out the pins. It is very hard to get them to move at first but gets easier as they start to move. I would recommend having a helper to hold the door upright as it will fall when the pin is removed from the hinge. Once the pins are out move the door and jack away from the body, to gain more access room the replace the bushings: two in the door side and two in the body side. Then slide door and jack back and align hinge holes and install new pins. I always grease the bushing and pins before installing. Drive the new pins all the way flush with the hinge and install the retainers. Reinstall the spring and reattach the wiring insulation.
What size are starter bolts for f250?
what size are the bolts that hold a starter on a 1995 f 250 powerstroke
How do you replace a door hinge pin?
First you need to get the right tools for the job and the right parts to fix the problem.There is a hinge pin in both the upper and lower hinges and four brass bushings and there is two different size bushings in each hinge and also two hinge pin retaining washers.as for the tools you need a spring compressor,jack,hammer,punch. First open the door all the way,put jack under door,I like to use a 2by4 board on top of the jack to help spread the weight of the door out a little,next if the door has a wireing harness in the jamp loosen the rubber insulation form both the door and the body this gives a couble of inches of slack in the wireing.Next use the spring compressor to remove the spring,then use the punch and hammer to drive out the pins.it is very hard to get them to move an first but gets easyer as they start to move.I would recomend having a helper to hold the door upright as it will fall when the pin is removed from the hinge.Onece the pins are out move the door and jack away from the body to gain more axcess room the replace the bushings,two in the door side and two in the body side,then slide door and jack back and align hinge holes and install new pins. I allways grease the bushing and pins before installing.Drive the new pins all the way flush with the hinge and install the retainers.Reinstall the spring and reattach the wireing insulation.
