What size is the front wheel bearing hub nut on a 1998 Chevy blazer s10 4x4?
36mm. You will also need an 18 mm box wrench to replace the bearing assembly.
Worn right front wheel bearing.
A front popping on the left of a 98 Blazer could be the brakes, steering, or wheel bearing. Check all three to find the cause.
Remove the tire and wheel from your Chevy Lumina. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing. Reverse the process to install the new front wheel bearing.
No. That is a factory sealed bearing.
no the hub and bearing are 1 peice and pretty easy to changs
The front wheel and hub bearing assemblies on a 1999 Chevrolet Blazer 4.3L are different depending on 2 or 4WD. The GM part# for the front 2WD is 15731627, and AC Delco FW127 for the 4WD. The real axle wheel bearings are also different and depend on the ring gear size of the differential.
Replacing a wheel bearing in your Chevrolet blazer will cost approximately $175 per bearing. You can save $125 by doing the work yourself.
Remove the tire and wheel from your 2001 Chevy Impala. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing. Reverse the process to install the new front wheel bearing.
Remove the tire and wheel from your 1997 Chevy Astro. Remove the axle end. Remove the wheel bearing nut. Remove the wheel bearing and the wheel seal. Reverse the process to install the new front wheel bearing.
The front wheel stud on a 1992 Chevy Blazer S10 can be changed by jacking the vehicle up, removing the wheel, and unbolting the caliper. The rotor assembly can then be removed, and the wheel stud pressed or hammered out of its seat.
rear wheel drive or 4x4 capable
Here is a link to some good instructions. http://reviews.ebay.com/ebaymotors/Chevy-Silverado-4x4-Front-Wheel-Hub-Bearing-Replacement_W0QQugidZ10000000002536494
It sounds like you have more probalem than wheel bearing. TAke it to a front end shop
If all goes well the job should take about an hour with proper tools and equipment. Keep in mind that if the hub/bearing assembly is rusted in, it could take longer.
If it is 4 wheel drive the front speed sensors are mounted into the front hub/bearing assemblies behind the brake rotor. If it is 2 wheel drive the front speed sensors are mounted to the spindle behind the rotor. In any case, just follow the speed sensor wire harness and it will lead you to the sensor.
Check related answers. There are several responses and are quite accurate.
It is rear wheel drive, until you shift it into 4 wheel drive.
You will need to remove the tire and wheel. Remove the axle end cap. Remove the wheel bearing seal. Remove the wheel bearing. Reverse the process to install the new will bearing.
Front or rear?
I paid $495.00 dollars
The spindle is what the front wheel is mounted on. It is the shaft that the wheel bearing slides up on.
Jack up the front end and support safely. Assuming this is a 4+4, remove wheel from problem side. Remove axle nut and washer. Remove brake caliper and brake pads. Remove brake caliper bracket. Remove brake rotor. Remove bolts holding wheel bearing assembly to knuckle. Disconnect ABS wheel speed sensor from vehicle harness if equipped. Remove wheel bearing assembly. Reverse procedure to install.
Need to know if it is 2 wheel drive or 4 wheel drive.
www.trailvoy.com All the answers for your Trailblazer from true enthusiasts.
y the chevys suck it cant help it
Never heard of a "front wheel modulator" on a S-10 Blazer. If you mean hub, it is the wheel bearing assembly. If you meant 4x4 shift solenoid then depends if it is shift on the fly or not. The ABS has a modulator, but not sure what you mean.
Yes it can be. I think you need to replace the whole hub assembly
No it`s sealed unit
2002 Monte carlos are not rear wheel drive
How to Remove the Steering wheel From a Chevy Blazer 2001
It has 1 big hub bearing per side and you can not service them. It has factory sealed bearings. If there bad then you must replace the bearing.
Have the front end checked via a wheel alignment
2 wheel drive, yes. 4 wheel drive, no.
Remove the tire and wheel from your Chevy Cavalier. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing.
If the truck is a 4 wheel drive, you can't repack the front wheel bearings. It has a sealed hub/bearing assembly that is not serviceable.
More then likey it is either the left are right front wheel bearing that is bad.
What could a clicking noise be comingfrom behind the wheel in the front end of my 1996 Chevy Blazer?
Check the CV Boot
Brakes are shot or a wheel bearing is bad.
Remove the tire and wheel from your 1997 Chevy Lumina. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing. Reverse the process to install the new wheel bearing.
Remove the wheel, remove the brake caliper, remove the brake rotor, disconnect wheel speed sensor from harness. remove the bearing hub, remove the wheel speed sensor from the bearing hub. Reverse order for install.
Brake wear indicators are telling you that brake pads need replacement? Bad CV joint? Bad wheel bearing?
Eventually the beraring can seize and lock the wheel. Also driving it will cause more damage and cost more to repair
1997 Chevy blazer front wheel lock when 4 wheel drive is engaged i have repalced rotors brakes and calipers could it be front hubs i jacked up blazer and front wheels turn hard like something is dragi?
tAKE THE FRONT DRIVE SHAFT LOOSE AND SEE IF IT STILL DOES IT IF IT DOES ITS THE FRONT CARRIER ASSEMBLY IF IT DONT ITS THE TRANSFERCASE
To replace the front wheel bearing on a Ford Fiesta, you will need to remove the wheel. Then with a hammer you can pull the old bearing out.
You can adjust some free play in your front wheel bearing by tightening the wheel bearing retaining nut. The best thing you can do is change the wheel bearing.
185 to 260 ft lbs this is the front center nut that holds axle and front wheel bearing together not wheel lug nuts
how do you replace the rear wheel bearing on a Chevy pick up
you dont, if you want to disconnect it then remove your front drive shaft.
the old ones have to be pressed out and new ones pressed back in.