0
What size of bolts are in the cross member assembly on a 95 eclipse?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the name of Member of the House of Assembly for Bulawayo South in Zimbabw?
The name of Member of the House of Assembly for Bulawayo South constituency in Zimbabwe is Cross Edward Graham.
How do you get the cross member holding your transfer case off?
remove the bolts at the frame rails
How do you replace 2002 dodge stratus headlamp?
i believe it has the same bezel design as the o4. there are 2 9/32" bolts on the top of the cross member (where the hood comes down and latches) above the head lamp. remove these bolts and pull the entire headlamp assembly. take your time with this last bit as it does not come out easy and if you force it you will brake stuff. on the back of the assembly is a big black plastic spanner nut. unscrew with your hand and there be the bulb. careful putting the new one in, it is indexed and only goes in one way.
How do you change the transmission fluid out in a 1994 Chevy truck with the cross member?
I'm having the same problem right now but this is the options I have come up with... If you can, remove the cross member. On my truck the bolts are rusted and seized, I tried copious amounts of penetrating oil to no avail. Be careful with heat because there is a gas line hidden on the frame member right above where the cross member is bolted on.(I'd avoid heat.) Option two... Drill holes through the cross member and make them large enough to get your socket through to the bolts. Care must be taken line the holes up with the bolts. It shouldn't weaken the cross member enough to worry about. Option three... and I do not know if this will work. Remove the bolts from the motor mounts and check and remove anything that can be crushed between the motor and the firewall. Then jack your engine and tranny up just enough to give you enough clearance to get those pesky bolts out. I think this would be a last resort though. Option four... Heat and bend a wrench to fit onto the bolts but still clear the cross member. Let the wrench cool down before use... Or maybe buy an offset box head wrench? Option five... When in doubt, phone your local Chevy dealer and ask to speak to a mechanic. Ask him (or her), something like... "Hey, how do you change the transmission fluid out in a 1994 Chevy truck with the cross member?" "Is there a special tool or trick?" Option six... Go to a Jiffy Lube or some such place and let them worry about it... Ask the price first. Good luck, please post what works best. NEW ANSWER: You don't have to do any of that stuff. Just get a 1/4 inch drive socket and it will fit right on the back bolts of the transmission pan and remove them. Then tilt pan foreward and it will come right out. It's no big job what so ever. Easy.
Location of front motor mount on 2000 mercury villager?
2000 Villager motor mount is located on the cross member dead center front of the vehicle. 2 bolts attached to the cross member pull out towards the alternator as well as the bolt through the mount itself. 17mm if I remember correctly.
Do you need to hoist the engine on a 1994 Camry to remove the oil pan?
NO! All you have to do is remove the exhaust downpipe and cross member that bolts up to the frame, then you have access to the oil pan.
Where is fuel filter on a 1988 Blazer?
It is inside of the driver's side frame rail, close to where the transmission cross member bolts to the frame. You will have to slide up under the truck to see it.
Do you have to remove the motor mount on a 1994 olds 88 royale to remove the water pump?
yes you have to lift the motor a few inches to get at all the bolts to the water pump. there should be a cross member near the back of the engine compartment. lift the engine until the brake resevour cap just gets to the cross member.
Where are the engine mounts 1997 crown vic?
Engine mounts on 1997 Crown Vic are under the engine above the front frame cross member. There are three bolts that attach the mount to the engine, and two bolts that connect the mount to the frame mounting points.
How do you get the rear bolts out of the oil pan on a 2002 Passat 1.8T engine do you have to raise the engine up the cross memeber seems to be in the way?
drop the cross member it takes only 15 minutes unbolt the struts on top so everything drops
How do you remove the top two bell housing bolts on a 1991 Toyota pickup?
you first remove the engine mounting brackets, then you place a jack under the transmission and remove the cross member bolts that hold the transmission up. after the bolts are removed you can lower the transmission down which will tilt the motor back allowing access to the top 2 bolts from the back side
How do you change headlights on a 2000 300m?
there is a cross member that covers the radiator and hold the headlights in place, there are about 10 bolts that need to come out, after removing them you should be able to take that out and have access to the headlight.
