What size socket is needed for axle nut on 2003 ford escape?
A 11/16 socket is needed to remove the 1984 Chevrolet pickup front axle hub assembly. The socket should be a five-point socket.
It is a 36 MM socket
hey i think its a 35mm socket
Just did mine, 33mil deep well socket will do the trick.
34 mm metric socket. They cost under teen bucks
I just did mine. It required a 33mm socket. Put a screwdriver through the hole in the caliper and into the cooling veins in the brake disk to prevent it from turning while loosening/tightening the axle nut.
inch and a quarter or one and five sixteenths
32mm and 34 don't fit...mine seem tapered?
1 and 11/16 inch
go to auto parts store they will tell you and should rent you one...
A 1 3/16" or a 30mm should work.
The socket size for the axle shaft not, on a 2006 Chevrolet cobalt, is three-quarter inch. The socket should be a five-point socket.
what size socket for front axle nut 1991 ford tempo
what size socket 92 ford tempo front axle
The nut on the front axle shaft uses a 1 11/16 inch socket. The nut on the front axle shaft uses a 1 11/16 inch socket.
30 mm. You need a normal chrome 12 pt socket instead of 6 pt impact.
In a 2003 it's located on the passenger side just above and slightly to the rear of the axle.
how to remove, or replace front right axle escape 2004
I have read that answer on our forum the other day! It is an odd size. Come to our enthusiasts forum for all your answers! www.trailvoy.com
how t change rar axle seal on 04 ford escape xlt
u need a 36mm socket!
If you go to Autozone they rent the socket. I believe it is a 4 or 5 prong socket. Not a conventional socket. Just tell them what year, what tonage (ie 1/2 ton, 3/4 ton etc), and that it's 4 wheel drive. Good luck. Lonjames1 at hotmail dot com
Remove wheels remove axle nut on drum brake side remove drum then axle is free place a socket over threads not to big u want socket just big enough not to damage threads hit socket with hammer to free it from ring gear and it is out!!
take off the drum stick a socket wrench through the hole in the axle and undue the four bolts then pull the axle out.
The axle shaft nut takes a 1 and 11/16 inch socket
Axle Nut .. 1994 Nissan Altima ... 36mm socket. You will need a 1/2" Impact or breaker bar. Most parts stores have a loaner program where you can borrower this socket.
On a 2003 Ford Explorer : Open the drivers door and there is an information sticker on the latch pillar You will find the axle code under " axle " Once you have the axle code you can determine the axle ratio
It is a 36mm nut/socket.
It requires a 1 and 11/16 inch socket to remove.
The axle shaft nut requires a 1 and 11/16 inch socket.
The front axle nut on the 4+4 should be 35mm. You can use a 1 3/8" deep socket but it will fit tight. On my 2000 Chevy s-10 the Nut was 36MM. The socket I bought at advanced auto says right on the package for GM axle nuts.
how do you replace left front seal on 2009 ford escape
32 or 36mm socket also 1 1/4 inch
It takes a 1 3/8 socket. That is one and three eights.
1 11/16 inch socket 1 11/16 inch socket
What size ball joint socket is needed for the upper ball joints on a 1997 Dodge b3500 with the 3600 front axle?
the big one. Go to Advance Auto Parts or Autozone and rent their ball joint press kit. It'll have a socket. You'll need a 3/4" drive socket wrench (Or a 1/2" to 3/4" adapter) and a long pole to slip over the handle.
Solenoids are behind the side cover on drivers side. Drivers axle and some engine movement needed not for a novise
It is 1 3/8" or 35mm
anywhere from 205 ft.lbs. to 221 ft.lbs. depending on what year Escape you have.
The front axle nut on a 1994 Plymouth Acclaim is 32mm OD. A 32mm axle nut socket should be available at most parts stores.
36mm should fit
Try a 30mm socket.
30mm 12pt Impact
32mm for the axle nuts.
With the correct sized socket, obviously.
1 11/16 inch socket
The axle nut is 1 11/16 in
once you remove the retaining tabs off of the washer that are covering the nuts, it takes a 34MM DEEP SOCKET
The front spindle nut on a 1991 Honda Civic requires a 32mm axle nut socket.