0
unplug old cord...plug in new cord
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What happens if you disconnect the power supply cord to the hard drive?
If you disconnect the power cord to the hard drive, when you turn the computer back on, the hard drive will not be operational. Additionally, if you leave the IDE (or SATA) cable connected when the power cable is disconnected, the system will take longer to POST because it will try to identify the device connected, but it will not be able to. If it is the only hard drive you have in your system, the computer won't boot up because your operating system is on the hard drive.
What does antenna power overload mean?
it means take the antenna out of the power outlet, it won't work!
A written plan describing the steps a company would take to restore computer operations in the event of a disaster?
recovery plan
The fan in a 250-watt power supply is malfunctioning. what action should you take?
Remove and replace the power supply.
How do you make a military aviation headset morale cord?
take the black and white wires(left and right audio) from the comm cord and strip them. do the same for red and green (mike high and mike low) get rid of the yellow wire/ cut it off (its not necessary) take your u-94 connector and wire it the same as you would for a interphone ground cord (george washington rode backwards yesterday, starting from 1-4 in this case.) Solder wires to proper connectors. take your ipod jack with wire and strip the wires solder the left and right ipod wires to white and black (do not solder them together, I.E do not habe black and white touching. ) plug in headset and ops check. (NOTE i have only got it to sound really good only a few times, maybe it was the speaker wire i was using but i wish you good luck.)
How do you change speed of homemade tattoo gun?
Depends on what source of power your using, its easier to change speed with batteries. With a cord you have to take it of and buy a special switch for it.
How do you power a 12v speaker bar?
take a 12v power cord splice the wire and reconnect
How do you connect a three prone power cord to the stove?
To connect a three prong power cord to a stove, remove the back of the stove and take off the old cord using a screwdriver. Connect the new cord according to the wire colors with the screwdriver.
What could happen if the coating on a power cord is damaged?
If the rubber coating on a power cord is damaged then you may get an electric shock which may take your life. More over if the power cord is made of many uninsulated wire they it may cause short-circuiting.
What is One step in a series of steps that take place in a chemical change?
One spet in a series of steps that take place in a chemical change? ( Answer:: ) ( Compound )
What could happen if rubber coating on a power cord is damaged?
If the rubber coating on a power cord is damaged then you may get an electric shock which may take your life. More over if the power cord is made of many uninsulated wire they it may cause short-circuiting.
Explain how you can setup power on and hard drive password?
To setup Power on Password in a computer take following steps :Turn on the computer , press 'Del' / F2 / F10 key.Go to Password Section & change the password.
Outline the steps to take when completing a room change in the hotel industry?
In order to take these reasonable steps one should note that lease note that licensees are expected.
One step in a series of steps that take place in a chemical change is a?
it is aperiodic table
How do you change a timing belt on 97 Mitsubishi mirage?
what steps do i take to change a timing belt for a '97 mitsubishi mirage
What could happen if the rubber coating on a power cord is damaged?
If the rubber coating on a power cord is damaged then you may get an electric shock which may take your life. More over if the power cord is made of many uninsulated wire they it may cause short-circuiting.
How do you take out the interference caused by plugging the power-cord into the HP DV6000 laptop or any laptop for that matter and causing flickering problems with an external syncmaster lcd?
Unplug the powercord and run on battery. I have an external that flickers with the cord in so i uplug it for awhile and it fixes it. Ive heard a two prong power cord fixes the problem.
