0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What kind of muffler clamp for 2003 Sunfire?
The type of clamp needed depends on where the clamp goes. Some may have a hanger that bolts to the frame. Others simply hold the pipe to the muffler. A local auto parts should have a kit to match the clamp that you have.
How do you replace the muffler on a 1989 Camaro RS and how difficult is it to do?
to change the muffler is really easy as long as u don't have to much rust unger it. all u need to do is take off the clamp that comes from the exhaust pipe and then the one clamp on the other side on the tail pipe. which is easier if u take it right off from the car and put back on later then if the rust isn't to bad the pipe would slide right out of the muffle. leaving u to put on a new one
What is the diameter of an exhaust system for a SUNFIRE 2000 2.2 going into the muffler and exiting the muffler also the clamp size?
put your mouth to the tail pipe!
Why does your muffler makes a rattle noise?
you may have a loose clamp holding it. You could have a rock in it.
What happends when heavy water comes out the muffler?
No heavy water in the muffler.
Change muffler on VW Golf?
Slice the neck off where it goes over the pipe ahead of it and slide the new one on & clamp into place. Make sure it's adusted properly before tightening as it won't loosen easily once tightened. Don't damage the inner neck taking the old muffler off.
How to change a muffler on Chevy S-10?
First off, crawl under the truck and see if your present muffler is welded on or clamped on. If it's welded on you will need to get an exhaust cutting tool from like Autozone and cut the old muffler off BUT before you do, get your new muffler and measure how far the inlet neck is and outlet neck is on the new muffler and this will tell you how far to cut. You could hold the new muffler up to the exhasut and mark how far from the muffler you need to cut. This is assumign you are replacing the bad muffler with a new one of the same size. Now there is an inlet pipe and and out let pipe on the muffler. You will also need to have the right size clamps. Pu tone clamp on the exhaust pipe going to the engine, then push the exhaust pipe into the inlet end of the muffler and slide the clamp down and snug it up but do not tighten it. Put the other clamp on the exhaust pipe towrd the rear of the truck, push the exhasut ipe into the outlet end of the muffler and then slide the clamp down onto the joint and snug up. if everythign aligns right, then tighten the clamps. Sometimes if you overtighten the clamps you will have exhaust leaks. If you cannot get the joints to seal, you may need to get your system welded. If you exhaust is leak free then you are done. After a few hot and cold cycles you may just want to crawl back under and check the bolts on the clamps just in case they came loose from the heat and cold cycles.
2000 Volvo V70 2.4 Turbo fuel filter location?
It is on the rear undercarriage of the vehicle, passenger side. Not too far from the muffler. Held in place by a clamp and a torx screw to lock the clamp in place. A17mm open end wrench is useful in prying off the hoses.
What do you do if your car muffler is falling off?
Go to a muffler shop and have it welded back on or replaced
What is the problem if you start your car something blow off your muffler?
The muffler is probably worn out and should be replaced.
Is taking the muffler off your exhaust bad?
No it is not a bad thing. The muffler was invented to muffle the sound. The muffler does not enhance anything. However, the muffler stops the engine being noisy and it is a LEGAL requirement to have one, if you take it off, the police will stop and fine you and your car may be crushed.
How do you remove the back wheel on a 2005 harley Davidson flht?
Jack up the bike, remove the right side saddlebag, loosen the exhaust clamp at the front of the right muffler and the two bolts supporting the rear of the muffler on the saddlebag support, remove the pull-off muffler on the right side, remove the rear brake caliper, loosen and remove rear axle while supporting the wheel, note location of spacers....move wheel ahead, slip drive belt off and remove wheel assembly
