0
The air compressor in GM trucks have no nut holding the clutch plate in place. The outside clutch plate is pressed in until the required air gap is accomplished, usually .010" to .015". This is done with a special puller that removes the plate and installs it. Your local auto parts store may have that tool for sale or rent.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you remove fan from 1993 ford econoline e150 4.9liter 6 cylinder?
You need to rent or buy a fan clutch removal tool kit. you need to remove the fan and clutch as one before you can separate the fan from the clutch.
How do you remove a fan clutch on a 1997 S10 pickup 2.2L?
The fan clutch on a 1997 S10 has a bolt on the center of the front. Remove the bolt while holding the clutch still. There is a special tool to grab the clutch fan from the rear to hold it while removing the bolt.
How does clutch to clutch fan center nut get loosen to remove clutch and fan assembly?
It depends on the vehicle, some are clockwise thread others counter clockwise. Either way it takes the correct wrench and a holding tool.
Is it possible to remove the transmission on a 1995 Saturn SC2 from the bottom without having to remove the engine?
no not at all not enough room.if it's standered and you need to replace the clutch you have just enough room to remove and install the clutch remember cut the clutch tool in half
How do you remove an AC clutch from a '92 Buick Century?
there is a tool called a "clutch removal tool" that can be purchased from j c whitney.,
How do you change the ac compressor clutch on a 2003 Chevy S10 pick up with 4.3 engine?
You need a special tool to remove and replace the clutch. Your local auto parts store can sell or maybe rent you the tool.
How do you remove clutch fan on a Ford F-250?
To remove the clutch fan on these Fords you will need to get a specialized tool from your local auto parts store. This tool allows to hold the water pump retaining bolts, then use a 1 7/8 wrench on the clutch fan. Check your belt routing label. This will tell you if your fan clutch is left hand thread.
How do I remove 1995 blazer fan clutch?
I think this one is easy...but not sure I wish someone woould tell if you need special tool or not
How do you replace chain drive sprocket on a husqvarna 41?
Remove the two bar nuts on the right side of your saw. Remove Bar cover, bar and chain. Remove the clutch, it is right handed thread. Remove the drive sprocket and replace. You will need a special tool for removing the clutch or make one. The clutch is reverse thread, you will have to turn it counterclockwise as you are looking at the clutch. you will need a special tool for the clutch and a piston stop to screw in the sparkplug hole so the crank will not turn. Sometimes you can activate the blade brake and take a brass punch and a hammer and put it on the outer edge of the lip on the clutch and smack the punch with the hammer and it will break free, and then do the opposite direction to tighten the new clutch back up.
Do you need special tool to remove clutch from 95 Isuzu rodeo engine?
It is no different than any other clutch, you didnt mention if its 4x4, then you will need two floorjacks. If you have changed a clutch before, this will be the same, and i recommend replacing the one piece rear main seal.
Is it hard to change a clutch in a 4-by-4 1994 Geo Tracker?
no just make sure to remove all 7 bolts and be sure to remove the starter also. when you are going to put the new one back in you will need a clutch allinment tool.
How do you install clutch Jeep Wrangler sport?
simple, but involved. You'll need to remove the transmission and transfer case ( do it separately as they are quite heavy together ) You 'll see the clutch attached to the flywheel still on the engine, remove the bolts holding it on ( pay attention to it's orientation as well as the clutch disk, hole placement as it will be easier to line up the new one ) Once the old one is removed, line up the new clutch ( use an alignment tool, your new clutch may come with one, this makes sure the clutch disk is lined up with the pilot bearing and the center of the clutch springs. tighten the clutch to torque specs, remove the alignment tool, and reinstall the trans. One note, I suggest replacing the throw out bearing ( this may include the clutch slave cylinder too ) before reinstalling, you don't want to do this again soon.
