0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What tool would be used to tighten a nut or bolt with a percise amount of twisting force?
torque wrench
What tyep of tool would be used to tighten a nut or bolt with an exact amount of twisting force?
torque wrench
What tool is designed to loosen or tighten cross head screws?
A Phillips-head screwdriver is a tool designed to loosen or tighten cross head screws. It gets its name from engineer, Henry F. Phillips.
What size tool for 86 Toyota head bolt?
size 9mm splin
What is the function of a hex bolt?
do you refer to a hexagonal bolt or a hex head bolt one has 6 sides one has 6 points inside the head hex bolt was originally made to replace a 4 sided bolt to make it easier to use hex head were originally made as a secure bolt that could not be removed without e special tool that was not available to the general public do you refer to a hexagonal bolt or a hex head bolt one has 6 sides one has 6 points inside the head hex bolt was originally made to replace a 4 sided bolt to make it easier to use hex head were originally made as a secure bolt that could not be removed without e special tool that was not available to the general public
How do you remove a magneto on a 96 blaster ATV?
With the tool, while they call this a flywheel puller it is a reverse thread nut, with a normal thread bolt in the center. After removing the nut holding on the mag, reverse thread the tool , then tighten the bolt in the center, off comes the mag.
How do you turn the fly wheel to tighten up the toquark converter 94 exployer?
They make a special tool to turn it or can use crank bolt or bump w/starter.
How do you remove the power steering pully on 1999 350 suburban with 4wd Is the Allen head bolt a right or left hand thread?
The Allen head is NOT a bolt. Go to an Auto parts store and get a Power Steering Pulley Remover tool. The pulley is pressed on, there will be instructions with the tool or ask the counter person.
How do you install pulley on power steering pump?
Before you remove the old pulley, it's best to note its position on the pump shaft, and its relation to the other pulleys. The simplest way to install the new pulley (or reinstall the old pulley) is to rent or buy a power steering pump pulley installer tool. Auto parts stores like Autozone, Kragen/O'Reilly, etc. rent these tools, with a full refund of the rental fee when you return the tool. Sometimes you can also use a simple bolt, nut, and washer (some new pulleys may come with this bolt; use a strong washer as it may bend or break). If you're using the simple bolt approach, thread the nut onto the bolt, then slide the washer onto the bolt. Set the pulley onto the end of the pump's shaft, then thread the tool, or simple bolt, into the pump's shaft. If you're using the tool, grab the end of its bolt head with a wrench to hold it still, while you use another wrench to rotate clockwise the part of the tool that pushes the pulley onto the shaft. If you're using a simple bolt/nut/washer, grab the end of the bolt's head with a wrench to hold it still, while you tighten the nut clockwise, and the washer and nut will push the pulley onto the shaft.
Is there a special tool for the tension on a2005 dodge 3.3 serpentine belt?
the idler pully makes the tension. to remove belt you use a wrench push tensioner in a direction that would loosen the belt as if you were trying to tighten or loosen the bolt holding the pulley on. carefull high tension.
Broken rear brake caliper bolt 93 Camry?
There is a tool called a bolt remover that can be used to get the bole out. A hole is drilled in the middle of the bolt then the tool is inserted and turned to back the bolt out.
What is that funny looking tool I saw my plumber use to tighten the pipe on my sink?
The tool you probably saw was a plumbers wrench. It uses and adjustable metal band to tighten pipes.
