0
size 9mm splin
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What tool reaches bolt to take off starter on '86 Toyota supra?
a vibrator
What is the function of a hex bolt?
do you refer to a hexagonal bolt or a hex head bolt one has 6 sides one has 6 points inside the head hex bolt was originally made to replace a 4 sided bolt to make it easier to use hex head were originally made as a secure bolt that could not be removed without e special tool that was not available to the general public do you refer to a hexagonal bolt or a hex head bolt one has 6 sides one has 6 points inside the head hex bolt was originally made to replace a 4 sided bolt to make it easier to use hex head were originally made as a secure bolt that could not be removed without e special tool that was not available to the general public
What size tool is required to remove headbolts from a 1999 Volkswagon Jetta?
Depending on the year the car was produced it may be a ribe or polydrive bit. its a new style bolt head similar to a torq bit but not the same. As for size that iam unsure of.
Do tool boxes fit all size truck beds?
There are different sizes of tool boxes for each bed size.Full Size Tool Boxes for large trucks like the Chevrolet Silverado or Ford F-150Compact Size Tool Boxes for smaller trucks like the Toyota TacomaDouble Cabin Size Tool Boxes for the smallest trucks like the Toyota Tacoma Double CabBecause these tool boxes typically lay on the bed rails, the width of the truck will dictate which tool box you should buy.Most web sites that sell tool boxes have dimensional charts that you can use to verify whether a particular tool box will fit your truck.
How do you remove the power steering pully on 1999 350 suburban with 4wd Is the Allen head bolt a right or left hand thread?
The Allen head is NOT a bolt. Go to an Auto parts store and get a Power Steering Pulley Remover tool. The pulley is pressed on, there will be instructions with the tool or ask the counter person.
How do you get a rounded off bolt loose from the drivers side bracket on a 350 sbc?
If you are still trying to take out the rounded bolt, and can access it pretty easily, try buying an extractor set at your local auto supply store or if you have a Harbor Freight store near you. Make sure you chose theextractor size that will best fit the center of your bolt head. Once you've figured what size you will be using, buy a drill bit ( for metal) the size of the extractor. Start by drilling the center of the bolt head, then with the extractor (which turns in the direction that the bolt loosens), turn out your bolt. Make sure you use a standard size socket on the extractor and not a deep socket. The deep socket has a tendency to slip and damage the extractor head. If you cannot access the bolt head easily, you can purchase specialty wrenches at just about any auto part supplier or sears (craftsman) that would do the job. Or go online and order a ratcheting chain from Mechanic tool supply inc. Hope the info was helpful. 73Lux
What kind and size of bolt head holds on the belt tensioner for a 2002 Ford Taurus SE vulcan -hex or torx?
For my 1999 Sable it is a Torx 15mm. I got one from O'Reilly and this is what they claimed is the correct tool. I was able to loosing the bolt on the tensioner, but the torx socket was somewhat loose. Captainjack75040
How do you remove a oil pan bolt that wont turn?
Heat the stuck bolt until it's red hot, let it cool completely, turn it out with proper size tool.
How do you remove the rear leaf spring from a 1992 Toyota pickup?
With a Toyota leaf spring removal tool. Just go to your local Toyota dealer, head into the parts dept, and tell 'em you need a leaf spring removal tool for a 92 pick up. If their any kind of dealer, they will have it in stock.
What is a Toyota special service tool?
This is usually refering to a Toyota specific tool or diagnostic device
How do you get the spare tire off from underneath a 2007 Toyota Highlander- tool is missing- I am turning the bolt to the LEFT- is that correct- it seems stuck?
Left is the correct direction, but...The tool that you are looking for is an 'adaptor socket'. A picture of it is located in the Owners Manual, page 346 (Section 4: In Case of an Emergency). You will need to contact a Toyota dealership to locate a replacement for this socket. The actual nomenclature for this part is 'Handle, Spare Wheel Carrier Bolt'. The part number is:51942-48010Do not attempt to use other tools on this bolt. It's a special '5-sided' bolt. You can possibly damage the bolt and/or release mechanism if you use an improper tool.I purchased my 2007 Toyota Highlander Hybrid used and this tool was missing as well. I went to a Kragen auto store and they couldn't find a socket that would fit.
How do you remove a rounded caliper mounting bolt on a 1998 Chevrolet Cavalier Z24?
Are you sure it rounded? Most of these bolts use an Allen Wrench so the outside of your bolt should be round but the inside should accept the L-shaped 6-sided tool. If the inside of the bolt is rounded from using the wrong size allen), then this is another problem to solve. Take a rotary cut-off tool with a thin wheal. Grind a slot in the bolt head. Try to use use large a slotted screw driver to turn the bolt. If this will not work, try drilling a hole in the bolt and use and "easy-out" or screw extractor (buy from a hardware store).
