0
Metallic
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why is cooper wire better than a rubber tube is?
it has better wire than a rubber tube
What happens to a swimming pool heater if a bond wire isn't attach?
If a malfunction occurred there is the possibility of electricity entering the pool. Therefore, the bond wire should always be attached.
What is gauge 8 means in copper electrical wire?
In cooper electrical wire, gauge 8 means the wire size assigned by the American Wire Gauge (AWG) system. That is why you always will hear about AWG WIRE, it's not the type of wire is the gauge that we are talking about. A gauge 8 wire will be used for connections requiring from 40-45 amps to a maximum of 73 amps. (24 for power transmission). Diameter of an 8 AWG wire is 0.12849 inches. 8 AWG is solid, not stranded.
What gauge of cooper service wire for 200A service to meter box and service panel?
bed
What is rw90 wire?
RW90 is a Canadian Type Wire
What type of chemical bond is copper wire?
Copper is bound by the metallic bond. Simply put, the valence electrons are held in a delocalised bond which is shared throughout the structure.
Why is cooper wire better than a rubber tube is?
it has better wire than a rubber tube
What makes the center of Thomas Edison's first light bulb?
cooper wire
What happens to a swimming pool heater if a bond wire isn't attach?
If a malfunction occurred there is the possibility of electricity entering the pool. Therefore, the bond wire should always be attached.
Is coil a type of wire?
yes coil is a type of wire
What type of losses occur in power transmission lines?
1. Wire resistance 2. Leakage around insulators 3. People stealing the power
How to use a wire pull tester?
A wire pull tester is used to perform wire pull testing, which is also known as bond pull testing. This method is the most common test used to find out the wire strength and it’s quality. A pull tester will measure a wire or bond’s failure based on the pulling force that caused the failure. Here is a step by step guide on how to use a wire pull tester. Step 1: There are many test conditions that can be used to perform a wire pull testing. Choose the double-bond peull testing method, as this test condition is widely used for traditional wire bonded devices. Step 2: Connect or tie one end of the wire to that of the die of the wire pull tester. Step 3: Connect or tie the unused end of the wire to the bonding post. Step 4: Apply the pull hook under the wire. A pull hook is one of the major parts of the wire pull tester, and it is used to apply the upward pulling force on the wire. Step 5: Make sure that the pull hook is placed at the highest point along the loop of the wire. The pulling force must be applied at 90 degrees or perpendicular to the die surface of the wire pull tester. If the die surface is horizontal then the pulling force must be applied vertically. Step 6: Another major part of the wire pull tester is an instrument that is used to measure the force at which the wire or bond breaks. This instrument helps the wire pull tester to measure the pulling force required to break the wire or bond. Record this measured force, also called breaking force, in grams-force. Step 7: It is important that the bond failures are recorded. There may so many reasons for the failure of bond. These reasons may include first bond or ball bond lifting, neck break, midspan wire break, heel break, wedge bond or second bond lifting. bond failure mode should be recorded so that the owner could investigate the reasons why such the failure occurred. First and second failure modes can not be accepted.
5 good conductors of heat and what its used for?
cooper, gold, aluminum, silver and iron are 5 good conductors of heat. cooper is used in electric wire
What is gauge 8 means in copper electrical wire?
In cooper electrical wire, gauge 8 means the wire size assigned by the American Wire Gauge (AWG) system. That is why you always will hear about AWG WIRE, it's not the type of wire is the gauge that we are talking about. A gauge 8 wire will be used for connections requiring from 40-45 amps to a maximum of 73 amps. (24 for power transmission). Diameter of an 8 AWG wire is 0.12849 inches. 8 AWG is solid, not stranded.
What is porcupine wire?
Porcupine wire is a type of barbed wire.
What is the effect of changing the type of wire?
When ever a wire is changed, change it by the same type, rating or capacity of wire.
Why did drMartin Cooper invented it?
he wanted people to BE ABLE TO carry their cell phones without A WIRE
