0
What type of coaxial cable is used when wiring a 10Base2 Ethernet network?
Wiki User
∙ 11y ago
rg6
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is 10base2?
10BaseT is an Ethernet cabling standard. 10BaseT devices can transfer data at a rate of up to 10 Mbps, and use twisted pairs of wires in their Ethernet cabling, as opposed to a coaxial cable. If you see wiring with an RJ-45 plug on the end, you probably have a 10BaseT or backwards-compatible product (such as 100BaseT or 1000BaseT).
What kind of wiring is commonly used in a bus topology?
A bus topology for a LAN will typically use coaxial cable, either 10Base5 (thicknet) or 10base2 (thin-net) copper wiring.
Where will you find the transceivers on a 100base-tx Ethernet network?
In the backbone wiring
On what type of network would you use BNC connectors?
There were 3 methods of using ethernet. At this point only the hub with cat5 wiring is being used. The two older methods were a. use of a very thick coax cable with each station employing a tranceiver and a tap into the coax. and b. thinner coax cables with BNC connectors daisy chained from station to station. Called 10base2. So this is an obselete 10M ethernet network.
What is the cable called that hooks your tv to dish?
Coaxial cable RG-6 is used for satellite TV wiring. If you have a HDTV, you would want to use a HDMI cord from your Dish Network receiver to your television. This will give you a great picture!
What does the term 1000base t mean?
The term 1000base t describes gigabit Ethernet over copper wiring. It states that the network segment can be only 100 meters in length and has to use a category 5 cable.
What is the wiring layout to connect 3 PCs with CAT5 cable without a hub or multiple NICs?
Go wireless. Or, the cheapest way is to get a simple hub (~$20), connect your PC's and share your apps. Presuming you are using an Ethernet NIC in each system, you cannot connect three computers with CAT5 cabling without a hub or multiple NICs. The various twisted-pair-based Ethernet standards (10BaseT, 100BaseTX, etc.) do NOT allow for more than two devices on a single physical network line, so there is no way to have three computers communicate along a single wire. Token Ring technology and the old 10Base5 (thinnet) or 10Base2 (thicknet) Ethernet standards were designed for multiple systems on a single physical connection.
What organization creates Ethernet standards?
he Telecommunications Industry Association/Electronics Industry Alliance (TIA/EIA) is responsible for establishing Ethernet and structured wiring standards
What is Ethernet in communication?
Ethernet is a family of computer networking technologies for local area networks (LANs) commercially introduced in 1980. Standardized in IEEE 802.3 , Ethernet has largely replaced competing wired LAN technologies. In the OSI reference system, Ethernet isat the Data Link layer. Systems communicating over Ethernet divide a stream of data into individual packets called frames . Each frame contains source and destination addresses and error-checking data so that damaged data can be detectedand re-transmitted. The standards comprise several wiring and signaling variants of the OSI physical layer in use with Ethernet. The original 10BASE5 Ethernetused coaxial cable as a shared medium . Later the coaxial cables were replaced by twisted pair and fiber optic links in conjunction with hubs or switches . Data rates were periodically increased from the original 10 megabits per second, to 100 gigabits per second. Since its commercial release, Ethernet has retained a good degree of compatibility. Features such as the 48-bit MAC address and Ethernet frame format have influenced other networking protocols
How do powerline network adapters work?
Power Line Networking connects all the computers in your home. It uses the electrical wiring to create a network, so through the electrical outlets next to each computer in your home you can connect all of your computers.
What organization is responsible for Ethernet standards?
The Telecommunications Industry Association/Electronics Industry Alliance (TIA/EIA) is responsible for establishing Ethernet and structured wiring standards
What is cat6 utp?
Category 6 Unshielded Twisted Pair, a specification for gigabit Ethernet wiring and connectors.
