10w30 oil
green coolant
10w30 oil
green coolant
10w30 oil
green coolant
To flush an engine of coolant in the engine of a Kian Spectra refer to the manual. Auto manuals can be purchased at auto part retails or in bookstores.
As a general rule, Yes you can remove your Jeep Wrangler's Hard Top. The best way to find out how is to refer to your Owner's Manual.
Blower Motor and Fan Replacement (RPO C42)REMOVAL PROCEDUREDisconnect the VCM or the PCM.Remove the coolant reservoir.Remove the rear coolant recovery reservoir mounting stud.Disconnect the cooling tube from the blower motor.Disconnect the electrical connector (1).Remove the 5 blower motor and tan assembly mounting bolts (2).Remove the blower motor and fan assembly.INSTALLATION PROCEDUREInstall the blower motor and fan assembly.NOTE: Refer to Fastener Notice in Service Precautions.Install the 5 blower motor and fan assembly mounting bolts (2).TightenTighten the bolts to 4.5 N.m (40 lb in) .Connect the electrical connector (1).Connect the cooling tube to the blower motor.Install the rear coolant recovery reservoir mounting stud.Install the coolant reservoir.Install the VCM or the PCM.Perform the heater function test. Refer to Function Test.For a description of the RPO Code(s) shown in this article/image, refer to the RPO Code List found at Vehicle/Application ID.Blower Motor and Fan Replacement (RPO C60 and C68)REMOVAL PROCEDURERemove the VCM.Remove the coolant reservoir.Remove the rear coolant recovery reservoir mounting stud.Disconnect the electrical connector from the blower motor.Position the VCM harness connectors out of the way.Remove the blower motor access cover retaining screws.IMPORTANT: Cut through the cover as straight as possible because the access cover must be replaced.Part of this repair is visible to the customer. In order to prevent damage to the component, do not cut any deeper than necessary in order to remove the access cover.Cut through the cover on the cut line (1) using a razor blade or a sham utility knife.Disconnect the cooling tube from the blower motor.Disconnect the electrical connector from the blower motor and fan assembly.Remove the blower motor and fan assembly mounting bolts.Remove the blower motor and fan assembly.INSTALLATION PROCEDUREInstall the blower motor and fan assembly.NOTE: Refer to Fastener Notice in Service Precautions.Install the blower motor and fan assembly mounting bolts.TightenTighten the bolts to 4.5 N.m (40 lb in) .Connect the cooling tube to the blower motor.Install the blower motor access cover.Install the blower motor access cover retaining screws.TightenTighten the screws to 2.5 N.m (22 lb in) .IMPORTANT: Do not use RTV. Apply the adhesive bead as straight as possible. Allow the adhesive to set for 15 minutes or until the adhesive becomes tacky.Seal the cut line using black weather-strip adhesive.Connect the electrical connector to the blower motor.Reposition the VCM harness connectors.Install the rear coolant recovery reservoir mounting stud.Install the coolant reservoir.Install the VCM.For a description of the RPO Code(s) shown in this article/image, refer to the RPO Code List found at Vehicle/Application ID.
The volume of the cylinders.
Don't know what gulf is but maw is the stomach and or digestive tract of sharks, guts. But it usually does not refer to the liver. Ken, the Shark Wrangler, WWW. shark wrangler .com
Refer to your user and service manual to see where the coolant temperature sensor is located in the VW Touareg V6.
The clio (all engines) are water cooled. Refer to your owner's manual which will tell you where to put the water if you want to top up the coolant level.
Refer to the link below
The water and coolant is put in the coolant reservoir for the location of this refer to the owners manual. It is best to do this when the engine is cold otherwise you run the risk of getting boiling water all over you. the mixture of coolant to water should be about 50/50.
well basically you need to fill your coolant system up I'm not familiar with Chevy's but refer to the car manual
this code is for the engine coolant temp. sensor. replace it.
Will vary with different engine and vehicle set-up types. Refer to owners manual.