0
What winnt32 switch is used to prevent dynamic update from running?
Wiki User
∙ 14y ago
it's /dudisable
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What should be used in order to prevent a duct mounted electric heater from being energized when the fan is not on?
An air sensing or air flow switch will do the job to prevent the heater from operating is there is no air flow from the fan.
What is the difference between iron clad double pole switch and double pole single throw switch?
Answer for USA, Canada and countries running a 60 Hz supply service.The difference between a double pole switch and a single pole switch is the use of the switch in the installation or equipment. A double pole switch is used when the voltage from two circuits has to be broken. An example of this is a 240 volt supply. A single pole switch is used where there is only a single supply voltage that has to be broken.
If you are running a photoelectric effect experiment and your light source cannot create an electric current which adjustment might cause an electric current to flow?
- select the adequate material for this experiment - switch to a light source with a shorter wavelength - switch to a light source with a higher intensity
Can you wire a light switch with only one 14-2 wire?
If the power feed goes directly to a fixture, or if you are wishing to switch a receptacle that is not now switched, you can us a 14-2 NM cable to install a "switch loop", provided the circuit is no larger than 15 amps. To do this, after running the 14-2 NM cable, connect the WHITE conductor of the 14-2 to the hot wire. At the switch, connect the black and white conductors to the switch terminals. At the fixture or receptacle, the black wire of the 14-2 NM cable now becomes your switch leg and is connected to the black conductor of the fixture or brass terminal of the receptacle. The NEC (for the United States) requires that the switch be fed with the white wire and the black wire be used as your switch leg.
How do you wire a double-pole single-throw switch?
In North America adouble pole single throw switch is usually used to disconnect a 240 voltload by disconnecting both hot supply wires. This is a safety procedure to prevent someone getting a shock when working on the load and thinking the supply is off just by opening the switch. Although just opening up one leg will turn the load off the remaining leg will still be "hot" to neutral and ground. The "hot" wires go to the top of the switch terminals and the load connects to the bottom two terminals on the switch.
Which criteria does the switch use to build dynamic Mac table?
address resolution protocol is used when the switch used to build the dynamic mac address table.
Were is the running lights switch on 92 Jeep Cherokee?
The switch should be the same as your headlight switch. If not then you will either need to install your own switch for the running lights or buy a new OEM switch module.
Switch off lights when engine is running on a Volvo V70?
your headlamp switch on the dashboard has a small screw on it. its a 3 position switch. turn it to switch daytime running lights off.
Where is the daylight switch on a 1995 Sunfire?
I presume you're asking about a daylight running light switch? As far as I know, there is no such switch in a Sunfire. They're on when the car is running and is gear. FriPilot
How do you prevent the windshield wipers from running regardless of the wiper switch position on a 1997 Toyota 4Runner?
unplug the wiper motor under your hook, its located at the back of the engine compartment on the passenger side
Why does your car stop running when the key is released?
If the engine stops running when the key is released, then the ignition switch is probably bad. The switch will need to be replaced.
What could prevent a PING from being sent to the workstations when they are connected through the switch?
What is the blue switch in the ashtray for in my 2007 tiburon?
The switch is not a switch. It is a light for the ashtray itself. It will only be on when the car has the headlights or running lights on.
Will brake switch control prevent a car from starting?
Not to my knowledge.
What would be the result if the MAC address table was flushed of dynamic entries?
The switch would broadcast frames out each port except the originating port until the switch learned all the MAC addresses connected to the switch.
99 Jeep Cherokee Laredo stay running after turn off the ignition switch?
99 jeep Cherokee Laredo stay running after turn off the ignition switch?
Where is the day light switch on a 1995 Sunfire?
I'm guessing that you want to be able to turn off the daytime running lights on your car. As far as I know, there is no such switch on the Sunfire. The daytime running lights are on whenever the car is running and is in gear.
