0
When the 10.0 Ω resistor starts to dissipate 100 W of power it will rupture. What minimum emf can be applied to this circuit to cause the resistor to rupture?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When a parallel LC circuit is tuned to resonance will the current be at a maximum or a minimum?
Inside the circuit loop between the inductor and capacitor the current will be at maximum. Outside the circuit the current through the LC tank circuit will be at minimum. It depends on where you are measuring it.
What minimum current will activate a ground fault circuit interrupter?
30 mAmp rating devices are commercially available.
Conclusion about thevenin's theorem?
Thevenin's theorem is a basic equivalence principle for circuit design. It can simplify a very complex circuit to a very simple equivalent. This is done by finding the Thevenin Resistance as well as the Thevenin voltage and current. Once these are known, the equivalent circuit is simply a voltage source in series with a resistance.
What is the minimum radius applied in sheet metal forming?
the industry standard is a minimum of twice material thickness. however, four times is better for thicker materials as this helps avoid stress cracking.
What is the Clipping circuit transfer function?
Transfer function is the relationship between output and input of a circuit. In the clipping circuit, the general transfer function is such that the transfer curve Av is less than 1 for passive limiter and greater than 0 to limit the maximum and minimum voltage value.
What should a complete circuit have a minimum of?
a power supply (eg: battery) and a load (eg: resistor) even a piece wire shorting two terminals of the power supply is a closed circuit
How do you get minimum and maximum value of resistor?
The minimum and maximum possible value is defined by the tolerance. To calculate the range of the resistor, simply add or remove the amount of the tolerance. For example, a 100Kohm resistor with 5% tolerance can range from 95Kohm through until 105Kohm. The lower the tolerance, the more accurate the resistor is.
When a parallel LC circuit is tuned to resonance will the current be at a maximum or a minimum?
Inside the circuit loop between the inductor and capacitor the current will be at maximum. Outside the circuit the current through the LC tank circuit will be at minimum. It depends on where you are measuring it.
When the circuit is said to be in resonance?
For a particular frequency if the current or the voltage of the circuit is Maximum or Minimum then that circuit is said to be in resonance .
What is a resistor that can be adjusted between minimum and maximum by turning a dial is called a what?
It is a variable resistor. Basically, the same as when you turn up or down the heat on an electrical oven or radio.
What parts to circuits have to contain?
The absolute minimum for a circuit is continuity. Without this it is not yet a circuit.
What is 30 percent off minimum wages?
30% off of minimum wages = 30% discount applied to the minimum wages = minimum wages - (30% * minimum wages)
A 1.2 k ohms resistor is placed across an 18-V source The minimum acceptable power rating for the resistor is?
1/2 watt (In theory you could use a "0.27 Watt" resistor, however there would be no safety factory and there is no standard value resistor that size.)
What is the minimum subscription of a public joint stock company?
the smallest number of shares or securities that may be applied for in a new issue is known as minimum subscription.
Resonance in an L-C-R AC Series circuit experiment?
At resonant frequency, current in the circuit is maximum.Impedence is minimum.
Why series a resistor with a load for a DC supply circuit?
Good question on a linear power supply a load is not really required since it is nothing but a low band power amplifier. ON a switching type power supply a minimum load is always required so the PWM has something to control to. Also the soft start circuit may blowup waiting for feedback .Critical circuit since it operates for a very short time. however the load is in parallel not in series.
Which circuit can decrease the fluorescent brightness to the minimum amount?
You need to purchase a Fluorescent dimmer switch, no circuit can dim the brightness of the light safely.
