0
When two nonmetallic-sheathed cables (Romex) enter a box is it permitted to bring both of the bare equipment grounding conductors directly to the grounding terminal of a receptacle using the terminal?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When you encounter a four-slot receptacle in a residential laundry room?
It allows for a separate equipment grounding conductor
Is a grounding 120 volt receptacle larger than an ordinary receptacle?
No, it just has an additional conductor to separate the neutral from the ground, and has a third prong in the receptacle to receive the appliance grounding conductor through the cordset.
The minimum acceptable tension force of the grounding contact in a receptacle is?
The retention force of the grounding blade of each electrical receptacle,shall be not less than 115g (4 ounces).
How to ground a gas meter?
n.e.c. 250.104 says the equipment grounding conductor run with circuit conductors feeding a gas appliance is permitted as bonding means
Is it safe to glue or tape an electrical socket in place?
No, the receptacle needs the screws in place to complete the bond between the metal component of the receptacle to the metal component in the receptacle's junction box. This bond is entirely separate from the grounding of the receptacle.
What do you call materials which can be used to discharge a charged object to the earth?
Grounding conductors
Does the Nec allow grounding electrode conductor to be run in conduit that has other conductors in the conduit and what code section?
No, the bare copper grounding conductor can not be in a conduit with other conductors. It can be in conduit by itself to provide mechanical protection for the wire.
What color are the terminals of a standard grounding type receptacle?
green wire is gr gray wire is neutra
What color are the terminal of a standard grounding-type receptacle?
green wire is gr gray wire is neutra
What is UL 467?
Grounding and Bonding EquipmentUL 4671 Scope1.1 This Standard applies to grounding and bonding equipment for use in accordance with the Canadian Electrical Code, Part I, CSA C22.1, in Canada or the National Electrical Code, NFPA 70, in the United States. 1.2 This Standard applies to the following grounding and bonding equipment:a) ground clamps, bonding devices, grounding bushings, water-meter shunts, grounding electrodes, and the like used in a grounding system;b) equipment for making electrical connections betweeni) the grounding conductors used in electrical power systems, non-current-carrying metal parts of electrical equipment, armored grounding wires, metal raceways, and the like; andii) grounding electrodes;c) equipment for making electrical connections betweeni) the grounding conductors used in telecommunications systems such as telephone, radio, CATV, network power broadband, and the like; andii) grounding electrodes; andd) hospital grounding jacks and mating grounding cord assemblies (for the United States, see Annex a).Notes:1) In Canada, "hospital grounding jacks" are not defined in CSA C22.1, Canadian Electrical Code, Part I.2) In Canada, "mating ground cord assemblies" are covered in CSA C22.2 No. 21 and CSA C22.2 No. 42.UL 467 references these Standards: 44 * 83 * 94 * 486A-486B * 486C * 514B * .Table of Contents for UL 467.
Why does in an electrical plug the earth pin is longer than other two...what is its main function?
The earth pin is called the equipment grounding conductor. The National Electric Code requires this conductor to be the first to make contact with the receptacle and the last to break contact with the receptacle, the way manufacturers comply with this requirement was to make the pin longer.
Define earth voltage and neutral voltage?
As the neutral point of an electrical supply system is often connected to earth ground, ground and neutral are closely related. Under certain conditions, a conductor used to connect to a system neutral is also used for grounding (earthing) of equipment and structures. Current carried on a grounding conductor can result in objectionable or dangerous voltages appearing on equipment enclosures, so the installation of grounding conductors and neutral conductors is carefully defined in electrical regulations. Where a neutral conductor is used also to connect equipment enclosures to earth, care must be taken that the neutral conductor never rises to a high voltage with respect to local ground.
