answersLogoWhite

0


Best Answer

ask your local Dodge dealer

User Avatar

Wiki User

โˆ™ 2009-06-13 00:57:40
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where are a list of Error codes for 1999 Dodge Ram 3500 cummins diesel?
Write your answer...
Submit
Related questions

What does p done code mean for 2001 dodge ram cummins diesel?

Its clear no codes everything ok


How do you get codes on 2001 dodge cummins?

With a scan tool.


What is the cause - for a 1999 dodge diesel - to be unable to rev - it suddenly goes into idle mode at various speeds - will change gears but only in idle - after 5 min off will work again?

Have the Cummins computer checked for trouble codes.


What does the error code P0700 mean on a 2003 Dodge diesel I found that it is Transmission control system MIL Request but what does that mean?

It means that you need to check the trans computer for codes..


How do you fix Error code 5 5 for a 1997 dodge van?

55 code is not an error code, it signals end of codes. If no other codes preceded it, you have no error codes.


How do you check error codes dodge caravan 2005?

With a scan tool.


What are the error codes for a 2001 Dodge Durango with a 5.9?

See link below for a complete list of OBDII codes.


How do you read error codes on a 2005 dodge caravan?

That requires a scan tool.


How do you get freightliner codes?

If you have the Detroit motor, you can read the fault codes off the dash. Call them in to any Freightliner dealer or Detroit Diesel mechanic, and they can tell you what those codes are. If you have the MBE4000, Cummins, or Caterpillar motors, you'll need to have the computer hooked up to read off the codes.


How do you find the error codes for a 2005 dodge ram with a 5.7L?

With an OBD2 scan tool.


What does 2001 dodge cummins p1693?

P1693 : Dtc detected in the companion module. You need to check the Ecm and Pcm for codes. Which ever did not have p1693 will have a code.


What do the error codes on 2004 dodge ram hemi mean?

The error codes indicate a failure has been detected. If you ask a question with the specific code number, with year, model, and engine we will try to answer.


What does an error code P doNE mean on dodge Dakota 2000?

It is done flashing codes. If that is the only message you got, there are no codes present.


What are the error codes for a 2003 dodge ram with a 5.7L?

go to auto zone and they will tell you for free


What is error code 1 on 88 Dodge Dakota v6?

The trouble codes on an 1988 Dakota are two digit codes. Code 1 does not exist.


Computer codes for 1998 dodge avenger?

I received these error codes for my 1998 Dodge Avenger, 6cyl. 2.5 What does these codes mean? Where would I start to fix these issues? ~THANK YOU ~ P0108 P1297 P0401


How do you reset the error codes on a 2002 dodge neon?

Use a scanner, or unhook battery for 5 minutes.


How do you review error codes for a 1995 Dodge Caravan?

turn power on off on off on. do not start just the power


How do you read 2001 Dodge Caravan error codes?

With a code reader that plugs in under the drivers side dash.


How do you check error codes on a 2003 dodge caravan?

Go to an auto parts store and ask them to run a scan. It's free and they check the codes with a special scan tool


Why won't the scanner read your 2008 dodge cummins?

They weren't designed to be compatible with a simple OBD2 scanner... you'll need someone with the Insite program and appropriate diagnostic connector to read codes.


What does error code 5 mean for a 1995 Dodge Caravan?

Engine codes start at 11 Could it be 55 which means N/A


How do you check error codes dodge 2005?

Take to your nearest partshouse ( Kragen, Autozone) They will usually plug it in and tell you what is wrong for free


How do you check error codes on 1997 dodge caravan?

With a scan tool.With a scan tool.


How do you get error codes for 2005 Dodge Caravan?

Put the key in the ignition, and turn it from "off" to "run" (WITHOUT STARTING) Three times. The odometer screen should then start to read out the stored fault codes.