0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What are switch legs?
When the neutral wire goes to the switch
How do you wire in a pull chain switch in a bathroom light fixture?
If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.
What part of a circuit is the wire cable or switch?
Wire is the transition material used to carry the electric current; the switch is the controller of that current.
What is common wire in a three way when all the wires are black?
If this is a new installation then you have a choice of picking any one you wand to make the common wire. Usually a three wire cable used for three way switching has a white, red and black wire in them. If this is an existing installation and you have misplaced which wire is the common you will have to go back to the switch to find the conductor used. Disconnect it from the switch and temporarily place it on the ground wire. Next go to the next junction box and start ringing the wires to ground. When you find which wire is grounded, this is the common conductor.
Is it safe to go from 12-3 wire to a 14-2 wire in the middle of a switch leg?
No. The wire size is dependent on the circuit protection. If the circuit uses a 20 amp breaker you need to run 12 AWG wire on all devices connected to that circuit.
No spark on 4hp Briggs no kill switch what does the wire that goes under the flywheel go to?
goes to kill switch
Will a loose kill switch wire on a out board motor cause bogging down?
A loose kill switch wire on your out board motor will cause the engine to lose power. As the kill switch loses contact the motor will begin to bog down or completely quit.
How do you wire up a kill switch for a mini moto?
On the side of the coil there is a little terminal if you take a wire form that to a switch and the other terminal on the switch and earth it out on the chassis..
How do you Disable the alarm kill switch on a 93 infinti j30t?
You pull out the kill switch and find the wires conecting it, you may not have to pull it out, just find the connecting wires and then with a tool cut the red wire ONLY THE RED WIRE other wise the alarm will go off, then your fine, and put it back in
How do you install a kill switch in a 81 Chevy truck?
Just put a switch in the power wire going to the coil.
By pass a kill switch on a gy6 scooter motor?
Isolate the wire going into kill switch [wrap some tape round it] so it cannot be earthed.
Light switch has 4 wire colors red and white and green and black which is the hot wire?
You have a 3 way switch. Your black wire is the hot wire. Your green wire is the ground wire. Your red and white wires go to the light and other switch. You should have gotten a wiring diagram with your switch.
Where is the stop switch on a Briggs and Stratton mower engine?
If the mower has a shift knob control for "Start" "Run" and 'Stop', the kill switch will be on the end of the cable that leads to the throttle bracket. If the mower has the safety handle that shuts off the mower when it is not depressed, the kill switch will be at the end of the cable that leads from the handle to the engine. If the mower is operated with an on-off ignition switch, the kill switch wire will be spliced to the switch "off" wire some where between the throttle cable and the switch.
How do you connect kill switch to 33cc gas scooter?
you run aline to the blak wire
How do you disable an ignition kill switch?
If I remember correctly, an ignition "Kill Switch" is a secret switch (or button) that must be pushed into a particular position for the ignition system to start the car.... That being said.... Simple. If it's a button that has to be pressed for the (key) ignition to start the car, duct tape it in place. Same for a "light switch" switch". OR...you could solder a wire to circumvent the switch..... :) Now remember...if the switch uses a thicker wire....you're going to want to use a thicker wire when you solder it :)
Is there a kill switch on a 1990 Nissan Maxima?
No kill swoitch. You either got a wire on the wrong place or burned a fuseable link.
Where does the white wire from the brake light switch on a 1998 s10 go?
Are you sure its not a ground wire?
