answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered
2006-10-03 13:03:52
2006-10-03 13:03:52

the knock sensor is located right in the middle of both left and right under the fuel rail. its on the block. find a picture of it, and you'll wonder what took you so long.

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


location right bank knock sensor 2003 5.3 z71


To the right of the Coolant temperature sensor. It has 1 wire connector


The knock sensor is on the right side of the motor on the block .It runs under the manafold.I can not get the retaining clip off.MIKE


The knock sensor for a 2.8 vr6 is located on the side of the block. It is right against the hose for the oil cooler.


There is NO right are left bank knock sensor. If you are smart you will replace BOTH of them while you have the intake off. You do have left and right bank oxygen senors, But not knock sensors.


As you are looking at your truck from the front the knock sensor shoud be on the passenger side right under the manifolds


the knock sensor is located on the lower passenger side of the block,right in front and slightly above the starter!


The Knock sesor is located on the backside of the block right underneath intake manifold.


it is a knock sensor that is used to adjust the ignition timing.


it's on the right front of the engine, not far from the crankshaft sensor


The knock sensor is located just below the intake manifold youll have to get under the car to see it, it goes right into the back of the block.


The function of the knock sensor ob a sensor on a 1991 4.3 s10 is to provide the computer the position of the crank shaft to give it the right information to get correct timing. That would be the crank position sensor. The knock sensor monitors the engine for spark knock (ping) so the ECM (Engine Control Module) can retard the timing to eliminate it.


Right next to the oil filter on the passenger side, it's on the right, and has a single wire connected to the back of it


It is on the engine, under the intake manifold, there should be a wire going to a sensor there. It is right in the middle.


The Right Front ABS wheel speed sensor is also used as a rough road sensor to assist the knock sensor in dectecting weather there is a knock from engine or bump from the road in order to adjust the spark and fuel.


it is right below on the intake, on the blocks backside.



the knock sensor is located on the driver side of the engine right under the intake it is about 1 in. it is connected so you will have to unplug it and then just screw it off


The circuit 1 knock sensor would be located on the lower right side of the engine block (passenger side). You will need to drain the coolant from the radiator and be prepared for the passenger side of the block to drain coolant when the knock sensor is removed. After you disconnect the electrical connection to the knock sensor, the knock sensor simply unthreads from the block counterclockwise. Apply a thread sealant to the threads of the new sensor and install, no need to over tighten, this is a tapered pipe thread.


It is right on top of the block, you have to remove the manifold and fuel injectors to get to it.


the knock sensor on a 95 eldorado is located underneath the passenger side right above the trans-axel by the vss switch on the back of the motor, if its knot there its underneath the manifold.


The knock sensor for a Honda CR-V 99 is located on top of the engine, under the intake. It is right beside of the number one cylinder.


usually on the side of the engine by the crankshaft. The knock sensor provides the computer the position of the crank shaft to give it the right information to get correct timing. A bad knock sensor will cause it to run ruff or not at all The knock sensor senses spark knock or pinging and sends that info to the ecm. The ecm then in turn retards the timing until the ping stops. You can test the knock sensor with the engine running, with a timing light attached watch the timing marks as you tap the engine block with a small hammer, you will see the timing retard briefly.


It is screewed into the side of the engine block, right in front of the starter.


knock sensor replacementFirst you'll need a 12mm ratcheting wrench. Fit the closed end of the wrench on the bolt attaching the knock sensor. You'll need to reach around the axcel and underneath the manifold. You may need to rotate the clamp out of the way that's on the hose right next to the sensor. Then, to crack the nut use a second wrench as leverage on the first wrench and loosen the nut. Last, disconnect the electrical plug to remove the knock sensor completely. knock sensor replacementFirst you'll need a 12mm ratcheting wrench. Fit the closed end of the wrench on the bolt attaching the knock sensor. You'll need to reach around the axel and underneath the manifold. You may need to rotate the clamp out of the way that's on the hose right next to the sensor. Then, to crack the nut use a second wrench as leverage on the first wrench and loosen the nut. Last, disconnect the electrical plug to remove the knock sensor completely.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.