Where is crankshaft position sensor located in a 1996 accord?
by what i understand its located between the crank pully and block.
1 person found this useful
Get an OBD II scan tool that will show live data. (most autoparts store have loaners, be sure to ask for one the will show live data) Pull up the RPM reading and crank the engine over. Hold accelerator to floor to shut off fuel to the engine. No reading find the crank sensor, inspect for damage, unp…lug electrical connector and clean it with electrcial contact cleaner spray and then plug the connector back into the sensor. Crank the engine while watching for RPM reading, again hold down the accelerator to prevent fuel flow to the engine. If you have RPM reading now sensor is ok, engine should run. I have seen to many Sables with just dirty connections at the crank sensor. The sensor by nature is very durable and should not fail. If you still do not see RPM you may have a internally damaged sensor or wiring problem. Corrosion sucks G That is correct but the best way to tell if the crank sensor is bad is if the car doesnt crank when its unpluged and cranks when its plugged up then its good. ( Full Answer )
Answer . \ndepending on engine size it could be in 4 different places.\n. \n2.5 liter is behind cruise control actuator.
Where is the crankshaft position sensor located on a 1996 Dodge Grand Caravan with 3.3 liter engine?
Just trying to help in my caravan its about 5 inches behind the crank pully but you might have to go under the van to locate it. On a 3.3L it goes through the bell housing.
I have Olds Intrigue 2000 3.5L. Needed to replace faulty crankshaft sensor. 3.5L engine has two of them. If engine is hard to start cold or hot and engine light is OK. Very common problem for this engine in Aurora 3.5 and Intrigue 3.5 is crankshaft position sensor. Which is located above and behind… starter. Starter must be removed first. ------------------------------------------------------------------------------------------------------------ Answer Lower right hand side of the engine just above the oil pan. Theres a single bolt that holds it in. ( Full Answer )
Answer . It is attached to the timing cover, just behind the harmonic balancer, on the lower part of the engine..
Where is the crankshaft position sensor and the camshaft position sensor located on a 1996 ford e 150?
Answer . the cranck sensor is on front of engine it reads the teeth on crank pulley.the cam sensor is on top of same side of engine.
Answer . If the engine is a 3100 V6, the crankshaft sensor is located behind the harmonic balancer (crankshaft pulley). You'll need a special puller to remove tha balancer. The sensor is attached by two bolts onto the timing cover. Replace sensor and plug it in. Repalce balancer& belts...you're …done! ( Full Answer )
V6 crank position sensor The crank position sensor is part of the distributor on a V6 All Fieros equipped with a distributor (1984 - 1986 4-cyl and 1985 to 1988 V6) have the crank sensor inside the distributor. It may also be known as a distributor pickup or HEI pickup. Fieros with DIS (1987 …to 1988 4 cylinder) have a crank sensor on the back side (engine side) of the ignition module extending into the engine block. The ignition module is the flat base that the ignition coils are attached to. ( Full Answer )
i have a 92 Dakota and the sensor was behind the engine closer to the passenger's side, if you want to get that becauseyour truck is stalling you should also consider buyin a computer, because i tried a bunch of stuff, and the computerwas the source of the problem
i was told today that it is located somewhere around the timing belt. the timing belt cover must be removed. I'll have to futher research before i attemp to change it myself. local mechanic told me he worked on one a month ago, changed plenty of parts, problem turned out to be the crank sensor. I've… changed my ignition switch and the main relay, still having problems. ( Full Answer )
The camshaft sensor is behind the water pump pulley and the crank sensor is mounted just above the crank pulley(dynamic balancer). If the crank sensor is bad . The car will simply DIE. If the cam sensor is bad it will simply not have sequential injector firing and driveability and MPG will be affect…ed. BOB Answer when the water pump pulley is removed you can see a sensor with 3 wires going to it at the top side of the crank shaft pulley. you might be able to see it with a flashlight and a mirror without removing anything. hope that's the right sensor. ( Full Answer )
Answer if it is a 454 or an 8.1 L it is in the bottom of the timing cover by the crank pulley. You will need a 10mm socket to remove the sensor.
Answer . \nIf this is a 3.0 (12 valve, non flex fuel) engine, there is no crank sensor. All CID info comes off the distributer, and the ignition system. If this is a flex fuel(not common) it is located on the RH front side of the engine. If this is a 3.0 SHO Yamaha engine, it is located on the l…ower RH rear of the engine.. Answer . \nIf this is a 3.0 (12 valve, non flex fuel) engine, there is no crank sensor. All CID info comes off the distributer, and the ignition system. If this is a flex fuel(not common) it is located on the RH front side of the engine. If this is a 3.0 SHO Yamaha engine, it is located on the lower RH rear of the engine. ( Full Answer )
stand on the driver side of the engine compartment & look below the distributor. It has a single bolt holding it in place. It's below the two hoses that you see. It is very hard to get to. today is my second day trying to replace mine. I just bought alot of extentions for my rachet set. hope it help…s. mike ( Full Answer )
Answer . depends on the engine but it is usually on the top of the bellhousing of the tranny. the crank sensor gets a pickup signal from the flywheel.
Crank Angle Sensor (location) i own a 98 Hyundai accent and the crankshaft position sensor is located just underneath the far right spark plug if your looking from the front of the car,about 5"-8". hope this helps.
It is located on the distributor under the cap and rotor Crank sensor should be on the front bottom of engine by the crank pulley
On a 1996 Plymouth Breeze, the crankshaft sensor can be found abovethe oil filter. It should be accessible without having to removeany other parts.
i don't have a definite aswer, but its most likely on the lower front end of the motor next to or behind the harmonic balancer
Location of 8.1 crank sensor . rear of engine block, drivers side, midway between top and bottom of block, one 10mm bolt holds it in place
On the back side of the harmonic balancer and onr bolt holds it into the timing cover
Answer . On the 2.0 and 2.4 engines, it's on the right rear of the engine. On the 2.5 engine, it's at the rear of the distributor. Rick I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technology. Visit my blog for cool articles and TSB's: http://fre…e-auto-repair-advice.blogspot.com ( Full Answer )
Answer . Bottom of the timing case on battery side..... look for the lowest wire connector in this area ...... best to get at from underneath.
Answer . This sensor provides a signal to an engine management computer or an ignition control module or igniter indicating the position of the crankshaft.
To test a crankshaft position sensor on a 1996 Jimmy Blazer, use aCKP sensor to test for voltage output. Compare the results tomanufacturer specifications.
The crankshaft position sensor is bolted to the bell housing of a96 Grand Cherokee. It is at the top of the bell housing, just onthe drivers side on a 4.0 L and on the passenger side on a V8.
ON the rim of the bell housing at 11:00 if you are facing front, 1:00 if you are standing in the front looking back.
Where is the crankshaft position sensor located on a 97 Honda Accord 2.2 non v tech and how do you replace it?
This would be located right behind the crankshaft. For the bestassistance, you can use the users manual to get it fixed.
\nThe crankshaft position sensor is behind the catalytic converter, in the area where the engine mates to the transaxle. Access is from below, and you should wait for it to cool down. \n. \nThis answer is specific to the DOHC 2.0L Zetec engine.
its on the front behind the front cover to replace it you need to take off the fan the a/c compressor and its bracket dont take off the lines to the compressor just unbolt it and move it out of your way to get enough access to thi timing system you have to take the timing belt off so mark on the pul…ly to align it after you are done ( Full Answer )
On our 1994 LHS it is located on the passenger side of the engine down by where the transmission is bolted to it. I had to remove the air intake pipe and push it out of the way, squeeze my left arm down through the opening to the left of the strut almost to my elbow and follow the connector wires to… the sensor. One 10mm socket removed the single bolt holding the sensor (a tight fit ). A quarter turn of the ratchet was enough to loosen the bolt so I could unscrew it with my fingers. Wiggle the old one out and replace. Takes about 15 minutes. ( Full Answer )
Esta ubicado en el lado del acompaÃ±ante si miras de frente muy cerca del alternador es de forma cilindrica en el blok del carro ahi va alojado fijate en un cable que es su conector. esta la costado izquerdo del auto si te pones de frente del carro es el del acompaÃ±ante tambien esta el alterna…dor en ese costado y fasil de localizar es de forma cilindrica y esta alojado en un extremo ( Full Answer )
Behind the vibration dampner pully Wrong On a Pontiac sunfire 1998 with the 2.4L it's on the front of the engine tucked aboue the oil filter the bolt is a 5/32 size and it's hard to see
try this link http://www.autozone.com/autozone/repairinfo/componentlocations/componentLocationMain.jsp?categoryNValue=4294963514&categoryName=Crankshaft+Position+Sensor# . basicly it is just above the oil filter. should have 3 wires running to it. If you are replacing it be sure to get the plug …that comes with the new part. when I changed mine it didnt mach, I found out later there is a plug that comes with new parts that changes then pins from round to flat. had to splice the new plug in. . Jafo33990 good luck ( Full Answer )
The crankshaft position sensor is on the same side of the engine asthe alternator and dip stick. It is about halfway between front andback, in the side of the block.
On the 4.0L It's on the bell housing of the flywheel. Open the hood, look from drivers side past the engine toward the rear of the vehicle (past firewall). Google the picture of what it looks like and you'll see it at 2 o'clock position on the bell housing. I'd suggest a ratchet crescent wrench to t…ake it off. B-tch to get to with regular ratchet. On the 4.7L it is on the side of the block, in front of the flywheel. ( Full Answer )
It is behind the starter Bendix passenger side U.S. spec car remove the starter to gain access for removal, its retainer bolt is a 10mm. for more details email : firstname.lastname@example.org or ans-bach@hotmail .com
Right on the bottom of the engine just after the fan shroud. You can see it, it is visible without removing anything.
I have a 1993 it is located behind the dampher or (Harmonic balancer). Be sure to adjust the gap to specifications on the new one usually held by 2 bolts. I got lucky and only had 1 bolt with a preset pin to hold in place. Your need a puller to remove and can be trying. Good luck.
\ni Would say not far from the The Face Bonnit ( Motor ) Engine ..
the crankshaft position sensor is located in between engine and trans passenger side. it easy to change . It is in the top of the bell housing on the pass side, under the trans dipstick tube.
The sensor is located on the right side of the the crankshaft attached by 2 bolts thru the timing cover it will be hard to see due to the pulley.
where is crankshaft position sensor and camshaft position sensor on a 2004 Jetta 2.0 gl
Take off the drivers side tire and its located on the side of the trans
I don't think that year has one. But if it does then it will be in the passenger side of the timing cover on the front of the engine right behind the harmonic balancer. 1 bolt holds it in place.
For the 3.0 v6, it's in the front of the engine just below the oil filter. For the 4 cyl, it's near the starter.
Answer . between the intake manifolf and the firewall. Answer . \neveryone should have a manual for their vehicle, and the library should have a professional manual available...in the reference section, you'll have to make copies of the important sections...good luck :) The crankshaft positi…on is always placed in and around the crankshaft pulley located at the front of the engine,often it is hidden behind the timing cover as these sensors are sensitive to road dust etc,be careful to observe torque specs on this sensor,the easiest way to locate is follow the only wire that runs behind the crankshaft pulley...r lyne ( Full Answer )
The crankshaft position sensor on this car is at the front of the motor on the passenger side. It is forward of the water pump inlet on a little mount. The toothed wheel it monitors is attached to the crankshaft behind the pulleys.
Looking from the front of the car, it is located on the right side at the back of the engine. Pelican parts says you have to remove the intake to get to it. But you can remove the MAF and the throttle body then you can see it positioned on the engine block. Some people have said they were able… to reach it from under the car on jack stands. Hope this helps. tbs04 ( Full Answer )
Pending on the year and engine size, some are located within the area of the harmonic balancer.