answersLogoWhite

0


Best Answer

The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.

User Avatar

Wiki User

โˆ™ 2014-06-19 13:54:52
This answer is:
๐Ÿ™
1
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is the crankshaft position sensor located on a 92 Buick Regal 3.1 V6?
Write your answer...
Submit
Related questions

Where is a Buick crankshaft position sensor?

The crankshaft position sensor on a Buick is located behind th Harmic balancer. It should have a wire plugged in to it.


Where is the Crankshaft sensor on a 2000 lesabre?

The 2000 Buick Regal 3.8L Crankshaft Position Sensor is located behind the harmonic balancer pulley.


How do you remove a Crankshaft Position Sensor?

how to remove crankshaft position sensor from 91 Buick Regal


Location of the crankshaft sensor on a 1998 Buick Century?

the crankshaft position sensor is located right behind the harmonic balancer mounted on the timing cover


Where is the crankshaft position sensor located in a 1998 Buick park ave?

The sensor is on the front cover near the water pump area.


2001 Buick Park Avenue where is the crankshaft position sensor?

The crankshaft position sensor is mounted on the front of the engine. It bolts on, and has one wiring plug.


Where is the crankshaft position sensor located on a 95 buick century?

behind the power steering pump on the passenger side of the engine


Where is crankshaft position sensor on 97 buick lesabre 3.8?

The Crankshaft Position Sensor is behind the crankshaft pulley (harmonic balancer). You will need a ½-inch drive breaker bar and appropriate socket.


1997 BUick LeSabre Custom location of crankshaft sensor?

the crankshaft sensor is located behind the harmonic balancer on the ft timing cover


Where is the fuel pump located in a 1998 Buick Park Avenue?

where is the crankshaft position sensor located on 1998 park ave


Where is crankshaft sensor located on 98 buick park ave?

Behind the harmonic balancer.


Where is the crankshaft sensor on 1995 buick regal 3.8l and how do you change it?

The crankshaft sensor is located behind the harmonic balacer. you will need a puller with special bolts to remove the balancer.


What is the fault code P0336 on a 1997 Buick lesabre?

The P0336 fault code on 1997 Buick Lesabre is a fault in the crankshaft position sensor circuit.


Where is the crankshaft sensor located on a 2000 buick park avenue?

Behind the crank pulley that your belt rides on!


Where is the ignition coil located on a 1990 Buick Riviera?

It uses a distributorless coil pack and a crankshaft trigger sensor.


Where is crankshaft position sensor located on a 1994 Buick Regal 3.8 and how do you replace it?

behind the crank shaft pulley. remove pulley and install new one make sure to replace it in the exact same spot it was before of you will tear up your new sensor


How do you install a CrankShaft Sensor in a 95 Buick Century?

Pull the front cover off of it, Behind the Crankshaft balancer, The sensor is there. a diagram of how to install a creckshaft sensor.


What is the crankshaft position sensor air gap on 1989 3.3 buick century?

That would be around three feet and five inches, give or take.


How do you replace the throttle position sensor on a 2003 Buick rendezvous?

I just purchased the throttle sensor for a 2003 Buick rendezvous and was wondering if anyone could tell me where it located and how easy is it to put in.


What are some possible problems on a 1993 Buick Skylark 3300 that can allow the engine to rotate but not start and no trouble codes?

I took it to a shop. It was the crankshaft position sensor.


Where is the crankshaft sensor on 2000 Buick Regal 3800 V6 and how do you change it?

The sensor is located in between the crank pulley and front cover, just to the lft of the crankshaft. In order to change the sensor, you must, first, remove the crank pulley. With the damper off, unplug the sensor, and pull off the plastic cover. The sensor is mounted with 2 bolts, just to the left of the crankshaft. You'll need a deep 15mm socket.


Where is the crankshaft sensor on your 99 buick regal?

Behind the crank pulley


Where is the crankshaft position sensor located on a 1989 buick century?

If it is a 2.8 or a 3.1, the crank shaft position sensor is located under the rear exhaust manifold, right above the transmission housing. Its a small sensor with a 8mm screw holding it in place. Be careful pulling it out, the are known to break off in the block housing. Then the fun really begins to get it out. If its a 3.3, or a 3.8, it is located under the harmonic balancer. You can take the sensor off without taking the harmonic off, but it is ultimately easier to take the harmonic off because you have to adjust the sensor to the timing ring on the harmonic. Its easier to do when its apart.


Show a diagram of a Buick park avenue engine?

show a diagram of a buick park avenue crankshaft sensor


Where is the camshaft position sensor located on a 1997 Buick Riviera?

the sensor is located behind the pulley for the water pump has one single 8mm bolt in it u need to remove pulley to get at it