Best Answer

How to know if air sensor not working on protege 2003

User Avatar

Wiki User

โˆ™ 2011-03-24 14:15:19
This answer is:
User Avatar
Study guides

Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is the 2003 Mazda Protege sensor 2?
Write your answer...
Related questions

Where is cylinder 2 located on a 2003 Mazda 6?

location cylinder 2 mazda protege

What is the firing order on a 2003 Mazda protege dx 2.0?

The firing order on a 2003 Mazda Protege DX 2.0 is 1, 4, 2, 5, 3, 6. The number 1 cylinder is on the back right as you face the engine.

Is premium gas necessary for the 2003 Mazda speed protege?

Yes. Check your turbocharged 2003 MazdaSpeed Protege Owner's Manual, Chapter 4, Page 2: Fuel Requirements: 91 Octane (R+M/2 Method) - this indicates Premium in the US market.

What size speakers are in a 2003 Mazda Protege 5?

Per Crutchfield 6 by 8 in the front and 6 1/2 in the back door. Hope this helps

What is the firing order for a 1993 Mazda Protege?

1 4 3 2

What is the firing order for a 1998 Mazda Protege?


What is a P1145 code on a 1996 Mazda Protege?

"Intake Valve Timing Control Position Sensor, RH Bank 2" wouldn't think it would be too much to fix on this car.

Where is bank 2 sensor 2 on a Mazda tribute?

The bank 2 is located on the driver side of the engine on the Mazda Tribute. The Sensor 2 is located after the catalytic converter.

Is the right O2 sensor on a '94 Mazda 626 es with a 2.5 6cyl on the front or rear manifold?

You did not specify which O2 sensor it is. Is it sensor 1 bank 1, sensor 2 bank 2, sensor 2 bank 1, or sensor 1 bank 2. There are four O2 sensors on a mazda 626

How many O2 sensors in a 98 Mazda Protege?

There are 2 sensors 1 upstream and 1 downstream to tell which one is bad use a scan tool if the code says bank 1 sensor 1 it's the upstream if it's bank 1 sensor 2 it's the downstream

Where is the intake air temperature sensor on 2003 Mazda 6?

The intake air temp sensor is coupled with the air flow sensor, just past the air filter, on top of the intake piping. It will have 2 screws holding it in. ~ P

Where is oxygen sensor bank 1 sensor 2 on a 2000 Mazda MPV?

That should be the sensor after the catalytic converter.

Were is the speed sensor found in the Mazda 323?

can you tell me where the my 03 plate Mazda 323 2 litre diesels speed sensor is located as its not working .ta

What is the correct spark plug wire layout for a 2000 Mazda Protege 1.8L?

Spark plug wire layout is also known as firing order. The correct firing order for the 2000 Mazda Protege 1.8L is 1-3-4-2 with a counterclockwise distributor rotation.

Does a Protege 2000 have a speed sensor if not equipped with cruise control and where is it?

Is it locate on the transmission, it is a 2 wire cable.

How do repair default code p0430 for 2003 Mazda tribute?

It is problem with catalyst bank 2, catalytic converter, 02 sensor, pcv system, air leaks.

Where is bank 1 sensor 2 on a 1997 Mazda millenia?

bank one is the rear head, sensor 2 would be the lower one

Where is the horn component located on a '98 Mazda Protege?

you have 2 horns' both close to the head litghts on left and right side

Which oxygen sensor is bank 2 sensor 2 on a 2003 GMC?

pass. side rear

Where is the heater core located on a 1992 Mazda Protege?

In dash. Look for 2 hoses on firewall-it's behind them. Replacement is not a job for a novice.

What is the torque for the alternator belt in a 1997 Mazda protege?

Tighten the belt until you have 1/2" of deflection at midpoint. I hope this helps you. Mark

Which one is cylinder two in Mazda 6 2003?

where is located cylinder 2 in 2004 Mazda 6 , V6?

Recently had transmission replaced 2 months ago Riding home car jerked and everything shut down restarted car and drove well What could have caused this problem with my 2000 Mazda Protege?

sounds like you need to replace cam positioning sensor on engine

Bank 2 sensor 2 on 2003 gmc Yukon XL?

pasenger side second sensor which is after the catylic converter

Where is the spark plug on a 2003 Mazda protege 5?

Looking at your engine you will see on top 2 black blocks (coils) and wires that come out of them into the engine. Pull the wires from the engine, and unscrew the coils from the top and remove them. Once you do, youll be able to see the plugs and remove them.