Cars & Vehicles
Ford Ranger

Where is the EGR Valve on your 1992 Ford Ranger with a 2.9 engine?

012

Top Answer
User Avatar
Wiki User
Answered
2013-11-11 22:16:25
2013-11-11 22:16:25

At the back of the passenger side on the engine.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


You could have the 2.9 liter , the 3.0 liter " Vulcan " or the 4.0 liter V6 engine . They are all over head valve / pushrod designs in a 1992 Ford Ranger


On a 1997 Ford Ranger , 4.0 EFI engine : The PCV valve is on the top of the drivers side engine valve cover , near the rear


The PCV valve, on your Ford Ranger 2.5 liter engine, is located on the outside of the air cleaner housing. The valve is on the back of the housing.


The 1995 Ford Ranger 3.0 liter engine PCV valve can be found on the top of the engine. The PCV valve will be on the back side of the air cleaner.


where is the PVC valve located on a 1990 ford ranger 2.3 L


on the backside of the engine by the firewall


The 1992 Ford Ranger ICM is located on the firewall in the engine compartment. The ICM will be on the drivers side of the firewall.


You can get a diagram for a 1992 Ford Ranger 3.0 engine from your local auto parts store. Repair books, such as Haynes, offer diagrams.


On a 2000 Ford Ranger , 4.0 liter EFI , V6 engine : The PCV valve is on top of the drivers side engine valve cover It is near the rear of the valve cover ( towards the firewall end )


On a 1996 Ford Ranger , 4.0 : The PCV valve is on top of the drivers side engine valve cover , near the rear of the valve cover


There was a 2.9 L - V6 engine available in the Ford Ranger from 1986 to 1992


On a 2000 Ford Ranger , 4.0 liter EFI , V6 engine : The PCV valve is on the drivers side engine valve cover , on the top of the valve cover , near the REAR of the cover


On your 1999 Ford Ranger , 4.0 liter EFI , V6 engine : I believe the EGR valve is just to the left of your engine oil dipstick ( when you look into the engine compartment from the drivers side ) The EGR valve is lower down and has a round shaped top


The PCV valve on a 1992 Ranger 3.0 V6 is on the drivers side and fits into the manifold cover near the firewall. There are 2 hoses which conect to the top of the PCV Valve.


No , the VIN " X " Ford engine is an Over Head Valve / pushrod design engine


On your 1992 Ford Ranger , 4.0 liter : The starter should be on the drivers side of the engine , low down , where the transmission bolts to the rear of the engine


no , over head valve ( pushrod )


No , the 3.0 liter " Vulcan " V6 engine in a 1999 Ford Ranger is an ( Over Head Valve / pushrod design engine )


According to Gates ( they make timing belts etc. ) the 2.3 liter - 4 cylinder engine in a 1989 Ford Ranger is NOT an interference engine so there should be no valve damage


NO - according to the Bosch website , a 1992 Ford Ranger , 3.0 L V6 engine takes Bosch oil filter # 3422


For a 1992 Ford Ranger , 2.9 V6 : With engine oil filter change : ( I believe that is 5.0 US. quarts )


where is the valve located on the 2002 ranger 4.0 liter 6 cyl?


I believe it is on the engine valve cover - drivers side


I believe it is on the valve cover , drivers side of engine , towards the rear


egr valve location on a 1997 ford ranger 23l



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.