answersLogoWhite

0


Best Answer

no adjustment of this clutch only a pedal freeplay adjustment

User Avatar

Wiki User

โˆ™ 2006-10-02 02:11:18
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is the blade to tighten up the screws for a clutch in a 1989 Nissan 240sx that is slipping?
Write your answer...
Submit
Related questions

How do you fix a clutch from slipping on a 90 Nissan 300zx twin turbo fairlady auto?

Tighten up the screws on he blade...


How do you adjust the clutch on a kawasaki bayou 300?

The clutch on a Kawasaki Bayou 300 can be adjusted with the use of the 2 adjusting screws. Turn them clockwise to tighten the clutch and counterclockwise to loosen the clutch.


How do you replace a blower heater motor resistor for a Nissan primera 2002?

By the clutch pedal two screws and a plug


Can i buy an electric cord attached drill that drives screws?

Yes, normally 110 or 240 volt units but these must have a graded slipping clutch with reversible drive switches.


How do you tighten the driver's side view mirror on a 1995 Nissan Altima?

There sould be 3 screws on the bottom were the mirror sits on the platform bracket, thigten them up


How do you tighten a bed that is rickity?

You can tighten all the screws on the support pieces of the frame.


How do you adjust the clutch on a 1995 Kawasaki Bayou?

on the right side of engine theres a black cover two screws take off theres a nut with flat tip screw driver on the inside loosen locknut turn clockwise to you feel resistance then turn counter clockwise until u feel resistance hold screwdriver still tighten lock nut ur done hope this helps it fixed my slipping clutch on my 95 220


What tool is used to tighten screws?

a screwdriver


How do you adjust a car door?

loosen #3 phillip head screws (2) on clasp on door pillar and push in to tighten door then re-tighten screws


What is used of screwdrivers?

They are used to loosen and tighten screws


What tool is designed to loosen or tighten cross head screws?

A Phillips-head screwdriver is a tool designed to loosen or tighten cross head screws. It gets its name from engineer, Henry F. Phillips.


How do you fix an interior door that has dropped?

Tighten the hinge screws


Where does screwdriver used?

The screwdriver is used to tighten and loosen screws.


Can you over tighten the screws on a battery terminal?

Yes u can.


How do you tighten screws on your nipple piercing for barbells?

The threaded balls on barbells are to be tightened by turning the ball clockwise to tighten and counter clockwise to loosen. grab one ball with one hand (left ball with the left hand) and turn the right ball clock wise with the right hand, when you can no longer tighten the ball without it slipping in your fingers both balls will be tight. There you go you have just tightened the balls on your barbell.


How do you tighten power steering belt?

I have a 1993 Nissan Altima, in which I had to loosen the Alternater Adjustment screws to get the old belt off. After replacing the belt, simply retighten the bolts until the belt is snug. Hope this helps.


Which tool is designed to loosen or tighten crosshead screws?

metal bars


How is a german plug wired?

you put the wires under the screws and tighten them


What is the function of an Allen wrench?

To tighten and loosen Allen head bolts


How do you remove a shift knob on a Nissan?

it screws off


Fan clutch removal for 1992 for aerostar 4.0?

== 2.3L Engine # Unbolt and remove the fan guard. # Disconnect the overflow tube from the shroud, remove the mounting screws and lift the shroud off the brackets. # Place the shroud behind the fan. # Remove the 4 clutch/fan assembly-to-pulley screws and remove the clutch/fan assembly. # Remove the 4 fan-to-clutch screws. To install: # Position the fan onto the clutch assembly, then install the retaining screws to 55-70 inch lbs. (6-8 Nm). # Position the clutch/fan assembly onto the pulley. Install the mounting screws to 12-18 ft. lbs. (16-24 Nm). # Position the fan shroud onto the radiator. Install the shroud mounting screws until snug. # Install the fan guard. 2.8L, 3.0L and 4.0L Engines # Remove the accessory drive belt. For more information, refer to Section 1. # If necessary for added clearance, remove the fan shroud retaining screws. CAUTIONThe large nut which attaches the fan clutch to the hub of the water pump shaft has a right-hand thread and must be rotated clockwise for removal. # Using the Fan Clutch Holding tool T84T-6312-C and Fan Clutch Nut Wrench T84T-6312-D, or their equivalents, loosen the large nut attaching the fan clutch to the water pump pulley. # Remove the fan/clutch assembly. # Remove the fan-to-clutch bolts, then separate the fan from the clutch assembly. Fig. 1: The cooling fan mounts to the fan clutch, which in turn attaches to the water pump pulley - 3.0L and 4.0L engines Fig. 2: Use the two fan clutch tools to remove the fan clutch from the water pump pulley To install: # Position the fan onto the clutch assembly, then install the fan-to-clutch mounting bolts to 53-71 inch lbs. (6-8 Nm). # Position the lower edge of the fan shroud in the lower retaining clips, then install the fan shroud attaching screws until snug. # Using the holding tool and clutch nut wrench, or equivalent, install the fan/clutch assembly onto the water pump pulley. Remember, the fan/clutch nut has a reverse thread and must be turned counterclockwise to tighten. Tighten the nut to 30-100 ft. lbs. (41-135 Nm). # Install the accessory drive belt.


Your flat screen monitor neck is loose what can you do tofix it?

check for screws that you can tighten.


What is the use of straight screwdriver?

The straight screwdriver is used to loosen or tighten screws;


How do you fix a refrigerator door that has dropped?

PUT IT INTO the slot and tighten it with screws. that's it


How do you tighten up the chain on a 2005 Raptor 660?

there are 2 screws on the swingarm that have lock nuts on them. loosen the locknuts, tighten the screws, and then tighten the lock nuts again. there should be very small lines engraved in each side of the swingarm that let you line up both sides. make sure they are