0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How the primer bulb on a weed eater works?
It sucks gas from the gas tank to the carborator using nothing but suction In general the primer bulb draws fuel from the tank through the carb and then returns it to the tank. Look for "carb" and "tank" on the primer bulb and make the respective connection. A line should come from the tank to the carb. Another from the carb to the primer. and another back to the tank.
How is the carburetor tubing connected to a weed eater?
In general the primer bulb draws fuel from the tank through the carb and then returns it to the tank. Look for "carb" and "tank" on the primer bulb and make the respective connection. A line should come from the tank to the carb. Another from the carb to the primer. and another back to the tank.
Why does the primer bulb on your toro snow thrower go flat?
There is an orifice in the primer assy. in the carb. that is plugged. You will have to remove and clean the primer assy.
Is there a carb filter on Briggs and stratton engines?
yes... near primer bulb
How do you Route fuel lines on a Poulan chain saw?
long line with filter goes from gas tank into carb shorter line goes to (INLET) suction side of primer bulb 3rd line goes from OUTLET side of primer bulb to other carb fitting
Where do fuel line go on poulan chainsaw?
byrumjr the line starts with the fuel filter in the tank and travels up to the carburetor out of the carburetor into the primer bulb, out of the primer bulb back in the tank raylago fuel line routing is as follows for all 2 cycle with primer ball external to the carb. remember the fuel is sucked into the carb, not puished or blown into the carb. the filtered line from the fuel tank goes to the "in" side of the carb. this is usually right next to the high speed adjustment screw on a walbro carb. the "out" line from the carb goes to the suction side of the primer ball, the output of the primer ball goes back to the return line in the fuel tank. if you have to run the choke and the carb high speed screw will not adjust properly, reverse the in and out lines to the carb.
A diagram for fuel lines for a poulan woodshark 1950?
Make sure you have the lines wright the skiney line from in the tankgoes to the top nipple on the carb the over flow line goes to the long nipple on the primer bulb and the other line off the primer bulb goes to bottom nipple on carb
What is the correct fuel line hook up for a zama carbuator with a primer bulb?
Connection nearest bulb is return to tank.
Briggs and stratton engine will only run if you keep pushing the primer bulb?
not getting gas.... needs carb cleaned
Where is the choke on a craftsman lawn mower?
depends on the engine Briggs or tech, does it have a primer bulb. but safe bet right next to the carb.
Why won't my Briggs and Stratton 4.5 HP lawn mower engine prime I have removed and cleaned the carb. The primer worked properly before disassembly. Now the bulb won't shoot fuel into the carb.?
The primer bulb probably needs to be replaced unless either one of the fuel hoses leading in and out of the primer bulb bracket is clogged. Be sure you mark how each fuel line goes before you remove the bulb so you can replace them correctly. Hmmm. Thinking more about it: If the primer worked properly before disassembly, chances are you crossed up the fuel lines when re-installing. Try switching them.
Why won't my Briggs and Stratton 4.5 HP lawn mower engine prime I have removed and cleaned the carb. The primer worked properly before disassembly. Now the bulb won't shoot fuel into the carb?
The primer bulb probably needs to be replaced unless either one of the fuel hoses leading in and out of the primer bulb bracket is clogged. Be sure you mark how each fuel line goes before you remove the bulb so you can replace them correctly. Hmmm. Thinking more about it: If the primer worked properly before disassembly, chances are you crossed up the fuel lines when re-installing. Try switching them.
